Thermostat for BMW E63 E64

Housing with calorstat for Bmw 6 Series:

Bmw E63 :

- 645ci 8 cyl 333hp from 05/2002 to 08/2005 (engine code n62b44a)
- 650i 8 cyl 367hp from 02/2005 to 07/2007 (engine code n62n48b)
- 650i 8 cyl 367hp from 04/2006 to 07/2010 (engine code n62b48b)

Bmw E64 :

- 645ci 8 cyl 333hp from 09/2002 to 08/2005 (engine code n62b44a)
- 650i 8 cyl 367hp from 02/2005 to 07/2007 (engine code n62b48b)
- 650i 8 cyl 367hp from 04/2006 to 07/2010 (engine code n62b48b)

Located on the mechanical water pump .

EGR valve thermostat located on exhaust gas cooler for Bmw 6 Series:

Bmw E63 :

- 635d 6 cyl 286hp from 05/2006 to 07/2010 (engine code m57n2)

Bmw E64 :

- 635d 6 cyl 286hp from 04/2006 to 07/2010 (engine code m57n2)

The EGR cooling thermostat is supplied with the gasket.

Housing with calorstat for BMW 6 Series:

Bmw E63 :

- 635d 6 cyl 286hp from 05/2006 to 07/2010 (engine code m57n2)

Bmw E64 :

- 635d 6 cyl 286hp from 04/2006 to 07/2010 (engine code m57n2)

This thermostat with connection pipe is sold with its gasket.

Housing with calorstat for Bmw 6 Series:

Bmw E63 :

- 630i 6 cyl 258hp from 02/2004 to 07/2007 (engine code n52b30a)
- 630i 6 cyl 272hp from 04/2006 to 07/2010 (engine code n53b30a)
- 630i 6 cyl 258hp from 05/2006 to 07/2010 (engine code n52b30n)

Bmw E64 :

- 630i 6 cyl 258hp from 03/2004 to 07/2007 (engine code n52b30a)
- 630i 6 cyl 272hp from 04/2006 to 07/2010 (engine code n53b30a)
- 630i 6 cyl 258hp from 05/2006 to 07/2010 (engine code n52b30n)

Gasket on calorstat housing for Bmw 6 Series:

Bmw 6 Series E63 :

- 635d 6 cyl 286hp from 05/2006 to 07/2010 (engine code m57n2)

Bmw 6 Series E64 :

- 635d 6 cyl 286hp from 04/2006 to 07/2010 (engine code m57n2)

Joint between calorstat and water pump.

This device is for fitting on an engine water hose.
It is used to control the activation of the electric cooling fan.

Setting range: 70 to 120 °C
For hose, inner diameter: 35 mm

Comes with wiring, relays and clamps

This device is for fitting on an engine water hose.
It is used to control the activation of the electric cooling fan.

Setting range: 70 to 120 °C
For hose, inner diameter: 28 mm

Comes with wiring, relays and clamps

This device is for fitting on an engine water hose.
It is used to control the activation of the electric cooling fan.

Setting range: 70 to 120 °C
For hose, inner diameter: 25 mm

Comes with wiring, relays and clamps

This device replaces the original radiator temperature sensor switch.
For triggering the original or replacement SPAL electric cooling fan

Setting range: 70 to 120 °C
Thread: M14 x 1.5 mm

Comes with wiring, relays and clamps

This device is for fitting on an engine water hose.
It is used to control the activation of the electric cooling fan.

Setting range: 70 to 120 °C
For hose, inner diameter: 38 mm

Comes with wiring, relays and clamps

This device is for fitting on an engine water hose.
It is used to control the activation of the electric cooling fan.

Setting range: 70 to 120 °C
For hose, inner diameter: 32 mm

Comes with wiring, relays and clamps

This device is for fitting on an engine water hose.
It is used to control the activation of the electric cooling fan.

Setting range: 70 to 120 °C
For hose, inner diameter: 45 mm

Comes with wiring, relays and clamps

This coolant thermostat housing is a new part designed to replace a worn, cracked or faulty component on a classic vehicle. It ensures the thermostat is held in place and provides a seal for the cooling circuit, thereby contributing to proper thermal management of the engine. As part of a restoration or careful maintenance programme, replacing this housing allows you to restore original functioning. An essential part for preserving the reliability and longevity of a classic engine.