Mecanic cleaners

MOTUL Brake Clean (750ml) is a high-powered, non-chlorinated spray degreaser for brakes and clutches, as well as for all metal and alloy parts and mechanical systems . Its exclusive formula has been specially developed to dissolve all traces of grease,oil and tar quickly and without rubbing.
It is ideal for use on brake pad residues and dust, brake shafts and axles, clutch discs and mechanisms, levers,shock absorber rods, chain guides and tensioners , etc...
It evaporates very quickly, leaving no residue.
Its other advantage is that it facilitates assembly and disassembly of mechanical parts.

INFORMATION: As this product is very powerful, we recommend not using it on plastics, rubbers, paints, varnishes or to clean motorcycle chains with O-Ring, X-Ring and Z-Ring O-rings!

ADVANTAGES :
- 750ml format for regular use or major maintenance.
- Cleans and degreases thoroughly without rubbing.
- Immediate action on spraying.
- Dries quickly without streaking.
- Does not damage metals, metal surfaces or alloys.

A must-have for your workshop!

ATTENTION: aerosols cannot be shipped by air (DOM TOM)!

Please observe the usual precautions.

A blend of solvents for extremewettability.
High pressure: 6 to 6.5 bars
Controlled evaporation.
Directional spray
Leaves no residue or traces
500 ml aerosol
Note,aerosols cannot be shipped by plane (French Overseas Departments and Territories)

Cleans and degreases the different parts of the carburetor, starter, injection wells or intake manifold. Used in Diesel to clean an EGR valve.
Eliminate quickly oils, gums, varnishes and other stubborn stains. Comes with a pipette to a specific use. The ideal product for any renovation carburetor or injection!
UNILOPAL: a professional range for the particular service.

LOCTITE SF 7200 joint stripper is an aerosol product designed to remove cured joints and traditional joints from metal joint faces before re-applying a new joint. Its action consists in softening them in 10 to 15 minutes, thus reducing the need for intense scraping operations. This CFC-free solvent-based cleaner is suitable for most surfaces, includingaluminum and other soft metals. Once applied, it covers the joint with a foam, preventing it from running out of the desired area, while allowing it to work for the required time. Your surfaces will be perfectly clean, with a minimum of scraping and a reduced risk of damaging joint surfaces.
It can also be used to easily remove adhesives, hardened oils and greases, scale, paint and varnish deposits, etc. from joint faces and metal surfaces.

WARNING: Its use is not recommended on plastics, as this product attacks paints!

Advantages :
- CFC-free, solvent-based cleaner.
- Ideal for quickly removing old joints.
- Can be used on most surfaces (except painted).
- Minimal scraping required (highly recommended for fragile, soft materials such as aluminum, copper and bronze).
- Does not run, even on vertical surfaces.

Recommendations for use:
- Protect painted surfaces, as this product attacks paint.
- Hold the aerosol upright, about 20-30cm from the surface to be treated, and apply as thick a coat as possible.
- Leave to act for 10 to 15 minutes to soften anaerobic joints, and 30 minutes for silicone joints.
- Remove the old, softened sealant with a spatula and simply wipe or clean the surface (repeat if necessary).
- Before applying the new joint compound, clean surfaces with a suitable cleaner such as LOCTITE 7063 (order no. UB25018 separately).

Please observe all safety precautions.

3-EN-UN TECHNIQUE 250ml contact cleaner removes grease, oil, polar dirt andoxide deposits , and prevents galvanization of electrical and electronic equipment, keeping it in good working order.It is particularly recommended for contactors, switches, terminals, fuse plates , printed circuits, relays, motorcycle controls , sensors, probes, etc...
Use at room temperature on cold surfaces.
Advantages of 3 In 1 Technical Contact Cleaner:- Removes deposits quickly.- Dries quickly without leaving residues.- No rinsing or wiping required.- Leaves a protective film.- Compatible with metals, vinyls, plastics and rubbers.- 250ml format for fast use and easy storage.
Aerosols cannot be shipped by air (DOM-TOM).
Please observe the safety precautions.

METAL 5 EGR4 Professional EGR Valve Cleaner - 400ml
Cleans air intake system, intake valves, EGR valve, air ducts and turbo immediately and effectively Dissolves gum, varnish, scale and deposits Easy to use, by spraying on engines running at various speeds Restores optimum air flowEnsures stable, even idling Reduces black exhaust emissions Restores and maintains engine power and fuel consumption Eliminates gaps during acceleration Gasoline and Diesel

MOTUL Brake Cleaner (400 ml) is a top of the line non-chlorinated super strength degreaser for brakes and mechanical parts. Its exclusive formula is specially developed to dissolve very quickly and without rubbing all traces of grease, oil and tar.
This brake cleaner evaporates very quickly without leaving a trace. It facilitates the assembly and the disassembly of the mechanical parts.

It being very powerful and it is recommended not to use it on plastics, paints and varnishes.

This spray contains a non-chlorinated degreaser which is perfect for cleaning your mechanical parts such as engine crankcases, spark plugs, levers, shock absorbers, rims, etc.

The formula enables you to dissolve all grease, oil or tar.

You can also use this product as a brake cleaner. It will remove dust and residue from brake pads and your clutch disc.

WD 40 SPECIALIST 400ml contact cleaner effectively dissolves oils, grease, dirt, dust and condensation on electrical or electronic equipment such as printed circuit boards, remote controls, read heads, printers, USB or micro-USB sockets on laptops, computers, games consoles, but also in the automotive industry(relays, fuses, switches, plugs, sockets, connectors, sensors, etc.).
After use, this product evaporates very quickly and leaves no traces. It is compatible with all metals, alloys, plastics and rubbers.
WD40 Specialist contact cleaner benefits:- Cleans and removes dirt, deposits, flux residues and condensation.- Penetrates easily and dries quickly without leaving residues.- Non-conductive (safe for electrical and electronic equipment).- Compatible with all metals, alloys, plastics and rubbers.- Two-position spray for broad or precise atomization.- NSF K2 approved.
Aerosols cannot be shipped by air (DOM-TOM).
Please observe all safety precautions.

BARDHAL Brake Cleaner (600ml) is a chlorine-free super degreaser spray for brakes.
Recommended by leading manufacturers, this immediate-action product removes all types of deposits and instantly eliminates oils, greases, tar, dust,hydrocarbon residues and brake fluid.
It can be applied to the entire braking system requiring cleaning or degreasing : ABS system gears , solid or ventilated discs , brake pads, rear brake linings, drums, calipers and their supports, bores, etc...
It dries in seconds, leaving no residue.
Its other advantage is its very high pressure, which enables it to remove even the most stubborn residues.

INFORMATION: As this product is ultra-powerful, we recommend not using it on plastics, rubber, paint or varnish!

ADVANTAGES :
- 600ml format for regular use or major maintenance.
- Removes oil, grease, tar and fresh glue.
- Cleans all types of deposits and residues.
- Ultra-powerful, immediate action.
- Dries quickly, leaving no residue.
- Eliminates whistling and extends the life of brake discs and pads.
- Dielectric, withstands up to 60,000 volts.

ATTENTION: Aerosols cannot be shipped by air (DOM TOM)!

Please take the appropriate precautions.

WD 40 Multifunction in 5-liter can format includes the same product solution as the aerosols. It can be used by consumers of WD40 as well as professional mechanics, garage owners and experienced DIY enthusiasts for all their renovation, mechanical and DIY work.Its economical canister format makes it particularly suitable for the thorough cleaning of spare parts for cars, bikes, scooters, motorcycles, etc...You can pour just the right amount of multi-purpose solution into a container, tub or other vessel as a soaking bath , so you can work simply and effectively with a brush, for example.Its fluidity will also enable you to use it as a spray with a sprayer (not supplied) for other uses.
WD40 has been used for many years in professional workshops to free rusted parts, remove moisture, protect, lubricate, eliminate squeaks, remove traces of residues, glues,adhesives etc...
Advantages of WD40 multi-purpose can:- Does not dry instantly.- Silicone- and chlorinated-solvent-free multi-purpose formula.- 5-liter format for professional use.- Can be used as a dip bath or spray.- Compatible with plastics, rubbers and all metals or alloys.- Non-conductive.
Please observe safety precautions.

When should you use it?
Irregular idling.
Acceleration flat spots.
Starting difficulties.
Loss of power.
Increase in fuel consumption.
Pollution.

Properties:
Cleans without removal.
Stabilises idling speed.
Removes deposits.

Instructions:
Pour the contents of the bottle into 20L of fuel, drive, fill up.

Recommendations:
Every 5,000 km.

WD-40 SPECIALIST Professional Degreaser - Spray - 1L
Thanks to its formula based on high-performance active agents, WD40 SPECIALIST Professional Degreaser quickly removes stubborn dirt without leaving residues. Non-abrasive and safe for many surfaces, including aluminum when used and diluted as recommended.
Advantages :Concentrated, dilutable formula - Fast, effective actionFormula enriched with active agents - Faster surface penetrationAqueous-based formula - Non-flammable, low VOCA single product for multiple uses : ideal for multi-purpose use in mechanical engineering, construction, domestic environments, etc...Multi-surface compatibility - Suitable for aluminum, plastic, ceramics, rubber and much more, when used according to recommended dilutions.NSF A8 certified - Formulated for the food industry. A potable water rinse is required after application to ensure food safety.

Dilution examples:Pure: Engines, oil stains, barbecues, lawnmowers...1:5: Car bumpers, garden furniture, tiles, grout...1:20: Bodywork, rubber, plastic parts, bicycles, painted surfaces, sports equipment, ceramics1:100: Windows
Directions for use :Before use, shake well to ensure proper dispersion of ingredients.Apply to the surface to be treated.On stubborn dirt, allow to act for a few seconds.Wipe off with a damp cloth and rinse with clean water.Can be used with high-pressure cleaners.

METAL 5 AIR5 Professional Carburetor and Intake Cleaner - 400ml
Cleans the inside and outside of carburetors and injection systems without disassembly Dissolves and removes all greasy deposits, gum and varnish that interfere with engine operation, without leaving residues Reduces fuel consumption and pollution Restores your engine's performance Protects cleaned parts from corrosion

Area of application:

- For surface preparation of glass and automotive parts (glass, plastic, metal)
- Application with lint-free cloth or brush.
- Unique silicone stain remover for optimal surface preparation.

Features :

- Universal cleaner, glass and plastic repair, silicone remover.
- Application with lint-free cloth or brush
- Very short drying time
-Product base: white spirit
- For surface preparation on paint, metal and plastic

Application :

- For preparing glazing operations and surfaces (glass, plastic, metal).
Apply with a clean cloth or brush (Teroson FL is a thinner that can be used with other Teroson products).

TECHNIQUE 3-EN-UN Super Degreaser (500ml) quickly and effectively removes oils, greases, brake dust, tar stains and other deposits or residues thanks to its powerful active solvents.An excellent brake cleaner, it is also recommended for refurbishing chains, engine parts, rollers, ball joints, blades, hand tools, lawnmowers, etc....It's ideal for cleaningclutch mechanisms, working on brake systems and any other mechanical operation requiring perfect decontamination before assembly or lubrication.
The benefits of Super Degreaser 3 in 1 Technique :- Fast, highly effective action without chlorinated solvents.- Leaves no traces even after drying.- Can be used between +5°C and +30°C- Compatible with all metals, alloys, plastics and rubbers.
ATTENTION: aerosols cannot be shipped by air (DOM TOM)!
Please take the appropriate precautions.