Fuel pump for BMW E63 E64

Fuel pump for Bmw 6 Series :

Bmw E63 :

- 645ci 8 cyl 333hp from 05/2002 to 08/2005 (engine code n62b44a)
- 650i 8 cyl 367hp from 02/2005 to 07/2007 (engine code n62n48b)
- 650i 8 cyl 367hp from 04/2006 to 07/2010 (engine code n62b48b)

Bmw E64 :

- 645ci 8 cyl 333hp from 09/2002 to 08/2005 (engine code n62b44a)
- 650i 8 cyl 367hp from 02/2005 to 07/2007 (engine code n62b48b)
- 650i 8 cyl 367hp from 04/2006 to 07/2010 (engine code n62b48b)

Please note! Compatible only with v8 versions of Bmw 6 Series E63 and E64.

Gaskets supplied.

Low-pressure, self-regulating, electric rotary petrol pump.

Extremely quiet
Body diameter: 38 mm
Pressure: 0.27 to 0.38 bar (4 to 5.5 psi)
Max. flow rate: 95 l/h
Gravity-operated, pushes gasoline but does not suck it up.

Can be mounted on 6V, in which case flow rate will be lower. Tip: gravity pump, to be mounted as close as possible to the reservoir, underneath it.

Electric fuel pump compatible with carburator mounts. This low pressure compact and quiet pumpis manufactured by American specialist Edelbrock.
As its operating pressure is between 4 and 7 PSI (0.27 - 0.48 bar), it thus offers a flow rate of about 144 L/H.
The pump comes with a screw-in fuel filter at the pump inlet

A push type, it mounts near the tank,in a horizontal position, rather than near the carbs. This fuel pump "pushes" the fuel, so it is not suction.
It is also compatible with E85 Ethanol

The ideal pump to use with one or more Weber!!

Dimensions:
- Length: 184mm with filter
- Width (including bracket) 80 mm
- Mounting center distance: 60 mm
- Fittings: 8mm

Essential for any twin-carburettor assembly
Pressure: 0,42 bar
Max. flow: approximately 114 L/H
Universal fitting: 12 volts
Soldwith two unions: 8 mm Recommendation : Install the pump on silentblocs tofilter operating noise. This pump vaccum.
Fit a Filter Kingto regulateandsave fuel.

Fullkit

Voltage: 12 volts
Flowrate: 132 l/h
Pressure: 450/500 g
Female thread: 1/8" x 27 NPTF
Male diameter: 8 mm
Weight: 750 g

Facet pumps run on 12 volts (3/4 amps),
They are self-adjusting, sealedand light, with integral filter (except on transistors). These pumpsreducethe Vapourlock effect by enabling a more regular supply
They mustbe fitted as close as possible to the tank in a vertical position, at aslow a level as possible.
For engines with carburettor
It is stronglyadvised to fit a Filter King regulator to obtain a constant pressure.

Full kit

Voltage: 12 volts
Flowrate: 113 l/h
Pressure: 280/350 g
Femalethread: 1/8" x 27 NPTF
Male diameter: 8 mm
Weight: 700 g

Facet pumps run on 12 volts (3/4 amps),
They are self-adjusting, sealedandlight, with integral filter (except on transistors). These pumps reduce the Vapourlock effect by enabling a more regular supply
They must befitted as close as possible to the tank in a vertical position, at as low alevelas possible.
For engines with carburettor
It is strongly advisedto fit a Filter King regulator to obtain a constant pressure.

The FACET Posi-Flo electric fuel pump is a universal solution suitable for restoration and maintenance of classic vehicles. It operates at 12 volts and delivers a pressure between 0.28 and 0.48 bar, making it compatible with many fuel supply configurations. Its operation is based on the push principle: it pushes fuel towards the engine but does not draw it in, and must therefore be installed accordingly. It is supplied with its mounting bracket, connector and a pre-filter, thus facilitating its installation during a replacement operation.

Electric fuel pump compatible with carburator mounts. This low pressure compact and quiet pump ismanufactured by American specialist Edelbrock.
As its operating pressure is between 2 and 3.5 PSI(0.14 - 0.24 bar), it thus offers a flow rate of approximately 113 L/H.
The pump comes with a screw-in fuel filter at the pump inlet

Push type, it mounts near the tank,in a horizontal position, rather than near the carbs. This fuel pump "pushes" the fuel, so it is not suction.
It is also compatible with E85 Ethanol

The ideal pump to use with one or more Weber!!

Dimensions:
- Length: 184mm with filter
- Width (including bracket) 80 mm
- Mounting center distance: 60 mm
- Fittings: 8mm

Pressure: 1.5 - 4 Psi / 0.10 - 0.28 Bar
Weight: 350 g
Decibels: 65 dB
Voltage: 12 Volts
Connector: 1/8 NPTF
Length: 85mm
Height: 60 mm
Lifespan: 6,000 hours
Made in the USA.
Supplied with mount, connector and pre-filter.
Works by gravity, pumps the fuelout but does not draw it in.

FACET low-pressure electric fuel pump for mounting at pressures from 4 to 7PSI (0.27 to 0.48 bar) for a maximum flow rate of 132.5 L/H.

A Filter King is recommended to regulate and save fuel.

Pressure: 4 - 7 Psi (0.27 to 0.48 bar)
Max. flow: 132.5 L/H
Universal mounting: 12 Volt
Inlet / outlet diameter: 8 mm
Anti-corrosion surface treatment
Made in the USA.
Supplied with mounting bracket, fitting and pre-filter.

For use on Cox Tip: Pump should be installed on silentblocs to filter out operating noise, lower than the tank, as it operates by gravity (pushing low-pressure petrol but not sucking it in).

Immersed pump for the fuel tank, ideal for significant engine tuning thanks to a maximum flow rate of 516l/h and the compatibility with E10 and E85 fuel.
To be adapted on your vehicle to replace the original petrol pump Flow rate:
- 330 l/h under a pressure of 5 bar
- 420 l/h under a pressure of 3 bar
Maximum permissible pressure: 8.3 bar
Dimensions: 130 x 50 mm

This fuel pump for Dyane - 6V is a quality reproduction.

This Dyane fuel pump is specific to early 6V models with a top-mounted inlet. It comes with 2 base gaskets, and has no priming lever.

We strongly recommend fitting a thermal shim to isolate the pump from the engine crankcase.

compatible models :

- DYANE (425) type AYA: 08/1967 to 01/1969
- DYANE 4 type AYA2: 03/1968 to 02/1970

Choose the benchmark in electric fuel pumps by opting for FACET quality!
For optimum performance, we recommend using a Filter King to regulate and save fuel.

Pressure: 0.10 to 0.28 Bars (1.5 to 4 PSI)
Max flow: 105.9 L /H
Universal mounting: 12 Volt
Anti-corrosion surface treatment
Made in the USA.
Supplied without fittings (order Ref: VC43504).

Tip: Pump to be installed on silentblocs to filter operating noise, lower than the tank as it works by gravity (pushes gasoline at low pressure but does not suck it in).

Full kit

Voltage: 12 volts
Flowrate: 152 l/h
Pressure: 450/500 g
Female thread:1/4" x 18 NPTF
Malediameter: 9 mm
Weight: 750 g

Facet pumpsrun on 12 volts (3/4 Amps),
They are self-adjusting, sealed and light,with integral filter (except on transistors). These pumps reduce the Vapourlock effect by enabling amore regular supply
They must be fitted asclose as possible to the tank in a vertical position, at as low a level aspossible.
For engines withcarburettor
It is strongly advised to fita Filter King regulator to obtain a constant pressure.