Transmission shaft

Universal driveshaftspider
Sold individually.

Rear drive shaft.
Left or right-hand side, sold per unit.
Diameter: 100 mm
Length: 537 - 541 mm

For VW Transporter T25/T3, Bus,
Caravelle, Kombi, Joker, Westfalia
Years: 08/1982 ->07/1992
since chassisno. 24-D-000 001->
Engines:
- 1600 Diesel (CS), Turbo-Diesel (JX)
-1700 Diesel (KY)
- 1900 Petrol water-cooled (DG, DF, SP, EY, GW)
- 2100 Petrol water-cooled (DJ, SR, SS, MV)
including Syncro model (4 x 4) with 14-inch wheels
Except for Automatic gearbox version.

Complete rear cardan shaft ready for installation, left or right for VOLKSWAGEN Combi Bay Window from 08/1967 to 07/1979all engines and manual gearboxes.The drive shaft is a key part of the vehicle, just as important as the engine or gearbox, and must not be neglected.Its bellows must always be in good condition, and not perforated, as they contain the grease that contributes to the lubrication and therefore the smooth running of the cardan shaft bearings, known as constant velocity joints.

For Golf 2 and Jetta 2:
- 1.8 with carburettor from 08/89->
- 1.8 GTi 8s 112hp
- 1.8 GTi 16s 139hp
- 1.8 GTi 8s G60 160hp (including Rallye)

For Corrado:
- 1.8 16s 136hp
- 1.8 8s G60 160hp
- 2.0 8s 115hp
- 2.0 16s 136hp

For Golf 1 cabriolet:
- 1.8 90hp (EX) from 08/1987->
- 1.8 112hp (DX) from 08/1984->
- 1.8 112hp (2H)

New axle shaft ready to mount
Length: 541 mm
Wheel end toothing: 38 cannelures
For vehicles without ABS system

For VW Transporter T4 (7D), Multivan
Years: 01/1996 ->06/2003
since chassis no. 70-T-200 001->
with manual gearbox:
left or right-hand side
- 1.9 Turbo-Diesel
- 2.0 Petrol
- 2.4 Diesel
- 2.5 Petrol
- 2.5 TDi
- 2.8 VR6 Petrol

with automatic gearbox:
- 2.5 TDi:right-hand side only

New ready-to-fit axle for VOLKSWAGEN TransporterT4 Multivan from 01/1996 to 06/2003 (incl. Syncro) from chassis no. 70-T-200001

With manual gearbox :
Left or right side
- 1.9 Turbo-Diesel
- 2.0 Petrol
- 2.4 Diesel
- 2.5 Petrol
- 2.5 TDi (except 151hp AHY, AXG)
- 2.8 VR6 Petrol

With automatic gearbox :
- 2.5Tdi: right-hand side only

New axle shaft ready to mount
Length: 528 mm
Wheel end toothing: 38 grooves
ABS crown: 48 mm
For vehicles with or without ABS system

For VW Transporter T4 (70), Multivan
Years: 09/1990 ->12/1995
up tochassisNo. ->70-T-199 999.
with manual gearbox:
left or right-hand side
- 1.8 Petrol
- 1.9 Diesel & Turbo-Diesel
- 2.0 Petrol
- 2.4 Diesel
- 2.5 Petrol
- 2.5 TDi

with automatic gearbox:
- 2.4 Diesel: right-hand side only
- 2.5 TDi: right-hand side only
- 2.5 Petrol: left-hand side only

Reconditioned passenger-side right front drives haft for Volkswagen Golf 1 Sedan, Cabriolet, Caddy and Jetta 1 up to 1983, in 90mm nuts:

Sedan :
- 1.5 and 1.6 Diesel and Turbo Diesel
- 1.5, 1.6 and 1.8 with carburetor
- 1.6 and 1.8 GTI

Cabriolet :
- 1.6 GTI (EG)
- 1.6 75hp from 08/1984 (EW)
- 1.8 90hp until 08/1987 (EX)
- 1.8 112hp until 08/1984 (DX)

Caddy :
- 1.6 Diesel
- 1.5, 1.6 and 1.8 Petrol

Technical specifications :
- Length: 750mm
- Center shaft outside diameter: 35mm
- Nut diameter: 90mm

Our reconditioned cardan shafts retain their original quality and authenticity, while preserving the durability and performance of the manufacturer's part developed specifically for your vehicle. They undergo rigorous testing according to a strict protocol. The result is a 100% guarantee of the quality and functionality of the reconditioned part.

Reconditioning is ecological and environmentally friendly. It takes around 33% less energy to recondition a part than to manufacture a new one.

This reconditioned cardan shaft is sold without deposits and without exchanging your old part.

Reconditioned driver's side left front drives haft for Volkswagen Golf 1 Sedan, Cabriolet, Caddy and Jetta 1 up to 1983, in 90mm nuts:

Sedan :
- 1.5 and 1.6 Diesel and Turbo Diesel
- 1.5, 1.6 and 1.8 with carburetor
- 1.6 and 1.8 GTI

Cabriolet :
- 1.6 GTI (EG)
- 1.6 75hp from 08/1984 (EW)
- 1.8 90hp until 08/1987 (EX)
- 1.8 112hp until 08/1984 (DX)

Caddy :
- 1.6 Diesel
- 1.5, 1.6 and 1.8 Petrol

Technical specifications :
- Length: 537mm
- Nut diameter: 90mm

Our reconditioned cardan shafts retain their original quality and authenticity, while preserving the durability and performance of the manufacturer's part developed specifically for your vehicle. They undergo rigorous testing according to a strict protocol. The result is a 100% guarantee of the quality and functionality of the reconditioned part.

Reconditioning is ecological and environmentally friendly. It takes around 33% less energy to recondition a part than to manufacture a new one.

This reconditioned cardan shaft is sold without deposits and without exchanging your old part.

For Golf 2 and Jetta 2:
- 1.8 with carburettor from 08/89->
- 1.8 GTi 8s 112hp
- 1.8 GTi 16s 139hp
- 1.8 GTi 8s G60 160hp (except Rallye)

For Corrado:
- 1.8 16s 136hp
- 1.8 8s G60 160hp
- 2.0 8s 115hp
- 2.0 16s 136hp

For Golf 1 cabriolet:
- 1.8 90hp (EX) from 08/1987->
- 1.8 112hp (DX) from 08/1984->
- 1.8 112hp (2H)

Transmission shaft without exchange, does not require the return of your old part,

For saloon:
- 320 is S14 with manual gearbox
- 324 td M21 with manual or automatic transmission
- 325 i M20 with manual or automatic transmission from 09/86

For Coupé:
- 318 is M42 with manual transmission
- 320 is S14 with manual transmission
- 325 i M20 with manual or automatic transmission from 09/86
- M3 S14 with manual transmission

For Touring:
- 316 i M40 with manual transmission
- 318 i M40 with manual transmission
- 320 i M20 with manual transmission
- 324 td M21 with manual or automatic transmission
- 325 i M20 with manual or automatic transmission

For convertible:
- 325 i M20 with manual or automatic transmission from 09/86
- M3 S14 with manual transmission

Ridex rear drive shaft for BMW 3 Series E30 :
Bmw 3 Series E30 Sedan :
- 324td 6cyl 115hp phase 2 from 02/1987 to 12/1990 (engine code M21D24) -> manual or automatic transmission- 325i 6cyl 170hp phase 1 from 09/1986 to 08/1987 (engine code M20B25) -> manual or automatic transmission- 325i 6cyl 170hp phase 2 from 09/1987 to 01/1991 (engine code M20B25) -> manual or automatic transmission
Bmw 3 Series E30 Coupé :
- 318is 136hp phase 2 from 02/1989 to 05/1991 (engine code M42B18) -> manual gearbox- 325i 6cyl 170hp phase 1 from 09/1986 to 08/1987 (engine code M20B25) -> manual or automatic gearbox- 325i 6cyl 170hp phase 2 from 09/1987 to 03/1991 (engine code M20B25) -> manual or automatic gearbox- M3 200hp (S14) from 07/1985 to 08/1989 -> manual gearbox- M3 cat. 195 hp (S14) from 05/1986 to 05/1989 -> manual gearbox
Bmw 3 Series E30 Touring :
- 316i 102hp from 06/1991 to 02/1994 (engine code M40B16) -> manual gearbox- 318i 115hp from 02/1989 to 02/1994 (engine code M40B18) -> manual gearbox- 320i 6cyl 129hp from 01/1988 to 04/1991 (engine code M20B20) -> manual gearbox- 325i 6cyl 170hp from 07/1987 to 04/1993 (engine code M20B25) -> manual or automatic gearbox- 324td 6cyl 115hp from 01/1988 to 05/1993 (engine code M21D24) -> manual or automatic gearbox
Bmw 3 Series E30 Cabriolet :
- 325i 6cyl 170hp from 09/1986 to 09/1990 (engine code M20B25) -> manual or automatic transmission- 325i 6cyl 170hp from 10/1990 to 01/1993 (engine code M20B25) -> manual or automatic gearbox- M3 cat. 195 hp (S14) from 06/1988 to 06/1989 -> manual gearbox- M3 200 hp (S14) from 06/1988 to 06/1989 -> manual gearbox- M3 cat. 215 hp (S14) from 03/1990 to 06/1991 -> manual gearbox
Supplied complete with bolts and mounting brackets.

Original VW left or right rear driveshaft for VW Transporter T25 / T3 from 05/1979 to 07/1992

For vehicles with manual gearbox
Length: 517 mm

Left-hand drive shaft for vehicles with manual gearbox,

For VW Golf 4 2-wheel drive and 4MOTION :
- 1.9 TDi 115hp (AJM, AUY)
- 1.9 TDi 130hp (ASZ)
- 1.9 TDi 150hp (ARL)

For VW Golf 4 4MOTION only:
- 1.9 TDi 100hp (ATD)
- 2.3 V5 150hp (AGZ)
- 2.3 V5 170hp (AQN)
- 2.8 V6 204hp (AQP, AUE, BDE)

New right front passenger drive shaft for Volkswagen Golf 2 and Scirocco in 90mm walnut: Golf 2 and Jetta 2 :- 1.3 Petrol- 1.6 petrol- 1.8 carburetor until 07/1989- 1.6 Diesel and Turbo Diesel Scirocco :- 1.6 and 1.8 carbureted from 1983 onwards ATTENTION: Not suitable for Syncro and Country versions! Supplied complete with gearbox-side gasket, grease and screws (6 screws and self-tightening nut). Technical specifications:- Nut diameter: 90mm- Length: 773mm- Number of teeth on wheel side: 22 This new cardan shaft is sold without deposit and without exchange of your old part.

For Golf 3 and Vento :
- 2.0 GTi 8s 115hp
- 2.0 GTi 16s 150hp
- 2.8 VR6 174hp
(Not for Syncro)

For Corrado :
- 2.9 VR6 190hp

XZN M8x1.25x48mm drive shaft mountingscrews for Porsche 924 from 1976 to 1988 :
- 924 2.0 - 125 hp (XJ/XK) from 1976 to 1985- 924 2.5 S - 150 hp (M44.07/M44.08) from 1986 to 1987- 924 2.5 S - 160 hp (M44.09/M44.10) from 1988- 924 2.0 Turbo - 170 hp (M31.01) from 1979 to 1980- 924 2.0 Turbo - 177 hp (M31.03) from 1981 to 1985- 924 2.0 Carrera GT - 210 hp (M31.50) from 1981
Technical data :- Dimensions: M8x48mm- Thread pitch: 1.25- Thread length: 48mm- Total length: 57mm- XZN head for multi-panel wrench
Requires 12 screws per gimbal, 6 screws per side (gimbal nut)
This product is sold individually.