Air hose

Boa ventilation ducting - Interior diameter 140 mm
Steel spring covered with fibreglass, impregnated with neoprene.
This spring is welded to form a continuous surface.
Temperature: - 55°C to + 260°C

This complete heat exchange sleeve kit for AMI - 5 pieces is specific to that car.

It includes:
- 2 x 500mm heat exchange sleeves
- 1 x 220mm demister sleeve
- 2 cardboard vent sleeves

These sleeves are secured with serflex type clamps, consider replacing them if they are rusted or fatigued.

Clamps and wing seals not included.

This complete heater muff kit for 2cv6 - 5 pieces is model-specific.

It includes:
- 2x 500mm heater muffs
- 1x 220mm demister muff
- 2x cardboard vent sleeves

These sleeves are fixed with serflex type collars, think of replacing them if they are rusted or tired.

Clamps and wing seals not included.

This complete heater muff kit for 2CV Van - 5 pieces is model-specific.

It includes:
- 2x 500mm heater muffs
- 1x 220mm demister muff
- 2x cardboard vent sleeves

These sleeves are fixed with serflex-type clamps - consider replacing them if they are rusted or tired.

Clamps and wing seals not included.

This cardboard vent seal for 2CV Vans with 435 engines is specific to models with 435cc engine.

It allows the heat released by the engine to be vented towards the front wings if it is not sent into the passenger compartment by the heating control.

This wing-mounted cardboard vent seal for 2CV Van AK350 et AK400 is specific to the 602cc engine models.

It allows the heat released by the engine to be vented towards the front wings if it is not sent into the passenger compartment by the heating control.
Made of rubber, it is much stronger than the original cardboard sleeves, which are heavily exposed to water and mud, and does not require a joint in the wings.

This cardboard vent seal for DYANE and Acadiane is mounted in the front wings.

It ensures that the cardboard sleeves are securely held and sealed.

This cardboard evacuation sleeve for DYANE 4 is specific to the 435cc engine models.

It allows the heat released by the engine to be vented towards the front wings if it is not sent into the passenger compartment by the heating control.

This corrugated cardboard demister for AMI 6 and AMI 8 cars - 85x50x220mm is compatible with all 2cvs and its derivatives after the 50s.

It consists of a layer of insulating foam and a corrugated cardboard sleeve so you can bend and secure it with seflex-type clamps.
Bevelled on one side, it connects to the defroster and demisting duct.

This cardboard vent sleeve gasket for AMI 6 and AMI 8 cars is mounted in the front wings.

It ensures that the cardboard vent sleeves are held securely and sealed.

This rubber fender vent for 2cv6 is specific to the 602cc engine model.

Itevacuates the heat generated by the engine to the front fenders when it is not sent to the passenger compartment by the heater control.
Made of rubber, it's much more resistant than the original cardboard sleeves, which are highly exposed to water and mud splashes, and doesn't require a joint in the fenders.

This bevelled cardboard demister for 2CV Van - 85x50x220mm is compatible with all 2CV and its derivatives after the 50s.

It is made up of a layer of insulating foam and a notched cardboard sleeve that allows it to be bent and fixed with seflex-type clamps.
Bevelled on one side, it connects to the defrosting and demisting duct.

This cardboard vent seal for 2CV Van is mounted to the front wings.

It ensures that the cardboard sleeves are securely held and sealed.

This cardboard heater sleeve for 2CV Van - 500mm is compatible with all post-50s models.

It is made up of a layer of insulating foam and a notched cardboard sleeve that allows it to be bent and fixed with seflex-type clamps.

Easy to cut, it is compatible with 435cc and 602cc engines.

This beveled cardboard demister sleeve for 2CV and derivatives - 85x50x220mm is compatible with all 2CV and derivatives after the 50s.

It consists of a layer of insulating foam and a notched cardboard sleeve which can be bent and fixed with seflex-type clamps.
Beveled on one side, it connects to the defrosting and demisting duct.

This cardboard heater sleeve for Mehari - 500mm is compatible with all post-50s models.

It is made up of a layer of insulating foam and a notched cardboard sleeve that allows it to be bent and fixed with seflex-type clamps.

Easy to cut, it is compatible with 435cc and 602cc engines.

Clamp for heater drain hose for Porsche 911 and 912 from 1968 to 1986 :
type F- 911 2.0 T / L / S from 1968- 911 2.0 T / E / S from 1969- 911 2.2 T / E / S from 1970 to 1971- 911 2.4 T / E / S from 1972 to 1973- 911 2.7 Carrera RS from 1973
G type - 911 2.7 from 1974 to 1977- 911 S 2.7 from 1974 to 1977- 911 Carrera 2.7 from 1974 to 1976- 911 Carrera 3.0 from 1976 to 1977- 911 SC 3.0 from 1978 to 1983- 911 Carrera 3.2 from 1984 to 1986
912 - 912 1.6 from 1968 to 1969

This seal is important because it protects the air filter's heat shield and seals the connection between the fitting and the rear cresecent plate, so it prevents the heat from escaping back into the engine compartment. VW original quality.
External diameter: 45mm, internal diameter: 25mm.

For VW Beetle, Karmann-Ghia, Camper
with Type 1 engine.

Insulated heating pipe sleeve
Between engine heat exchanger and chassis.
Outside diameters in mm: 50 on the heat exchanger side/50 on the chassis side
L = 356 mm
Left or right mounting

For VW Beetle, Karmann-Ghia
Years: ->07/1964

Insulated heating pipe sleeve
Between engine heat exchanger and chassis.
Left side
Outside diameters in mm: 60 heat exchanger side/60 chassis side
L = 356 ~ 370 mm

For VW Beetle, Karmann-Ghia and Trekker 181
Years: 08/1967 ->