Shock absorber bearing

Suitable for:
- Golf 2 & Jetta 2 all models except G60

Reinforced upper rear suspensionbearing , brand MEYLE HD range, right passenger side or left driver side for BMW Z3 E36 with standard chassis or M-Technic chassis:

Roadster :
- 1.8 4cyl 115hp phase 1 from 05/1997 to 09/1998 (engine code M43B18)
- 1.9 16V 4cyl 140hp phase 1 from 05/1997 to 04/1999 (engine code M44B19)
- 1.8 4cyl 1.9L 118hp phase 2 from 04/1999 to 08/2000 (engine code M43B19TU)
- 1.9i 4cyl 118hp phase 2 from 08/2000 to 06/2002 (engine code M43B19TU)
- 2.2i 170hp phase 2 from 12/1999 to 06/2002 (engine code M54B22)
- 2.8 192hp phase 1 from 05/1997 to 08/1998 (engine code M52B28)
- 2.8 192hp phase 1 from 09/1998 to 03/1999 (engine code M52B28TU)
- 2.8 193hp phase 2 from 04/1999 to 05/2000 (engine code M52B28TU)
- 3.0i 231hp phase 2 from 09/1999 to 06/2002 (engine code M54B30)
Coupé :
- 2.8 192hp phase 1 from 05/1997 to 08/1998 (engine code M52B28)
- 2.8 193hp phase 1 from 09/1998 to 03/1999 (engine code M52B28TU)
- 2.8 193hp phase 2 from 04/1999 to 05/2000 (engine code M52B28TU)
- 3.0i 231hp from 09/1999 to 06/2002 (engine code M54B30)

Suitable for 10mm diameter shock absorber rod.
Supplied with gasket.
Spacer washer and nuts not supplied.

This high-quality rear suspension cup offers optimized performance compared with the original version: design faults are corrected, and the materials used provide greater strength, longer life and improved operating efficiency.

WARNING: When replacing your bearings, it is imperative to replace and reinstall the spacer washer located under each one (see photo). Otherwise, the bearing silentblocks will come out of their housings and the shock absorbers will "pass through" the body, which could cause serious damage to your vehicle.

This product is sold individually.

Bottom diameter: 45mm
Height lower part: 23mm

Reinforced upper rear suspensionbearing , brand MEYLE HD range, right passenger side or left driver side for BMW 3 Series E30 with standard chassis or M-Technic chassis:

Sedan, Coupé and Touring:
- All petrol and diesel models from 12/1981 to 02/1994 (including 325ix 4-wheel drive and M3).

Cabriolet :
- 318i 115hp from 07/1990 to 04/1993 (engine code M40B18)
- 320i 6cyl 129hp from 04/1986 to 09/1990 (engine code M20B20)
- 320i 6cyl 129hp from 10/1990 to 01/1993 (engine code M20B20)

ATTENTION: Not suitable for Cabriolet 325i!

Suitable for 10mm diameter shock absorber rod.
Supplied with gasket.
Conical washer and nuts not supplied.

This high-quality rear suspension cup offers optimized performance compared with the original version: design faults are corrected, and the materials used provide greater strength, longer life and improved operating efficiency.

WARNING: When replacing your bearings, it is imperative to replace and reinstall the conical washer underneath each one (see photo). Otherwise, the bearing silentblocks will come out of their housings and the shock absorbers will pass "through" the body, which could cause serious damage to your vehicle.

This product is sold individually.

Bottom diameter: 45mm
Height lower part: 23mm

Reinforced upper rear suspensionbearing , brand MEYLE HD range, right passenger side or left driver side for BMW 3 series E36 and E46:

E36 Sedan, Touring, Coupé, Cabriolet and Compact:
- All models with standard or M-Technic chassis from 11/1989 to 08/2000 (except M3)

E46 Sedan, Touring, Coupé and Compact :
- All models with standard or M-Technic chassis from 04/1997 to 07/2005 (except M3 and Cabriolet)

Suitable for 10mm diameter shock absorber rod.
Supplied with gasket.
Conical washer and nuts not supplied.

This high-quality rear suspension cup offers optimized performance compared with the original version: design faults are corrected, and the materials used provide greater strength, longer life and improved operating efficiency.

WARNING: When replacing your bearings, it is imperative to replace and reinstall the conical washer underneath each one (see photo). Otherwise, the bearing silentblocks will come out of their housings and the shock absorbers will pass "through" the body, which could cause serious damage to your vehicle.

This product is sold individually.

Bottom diameter: 45mm
Height lower part: 23mm

Upper bearing suspension left or right (top mounting on the damper rod),sold individually.

Suitable for :
- Golf 1 Berline & Cabriolet 07/77->
- Golf 1 Caddy (pick-up)
- Jetta 1
- Scirocco

1 reinforced pad + 1 reinforced bearing for LH or RH side.

This part provides optimum quality in relation to the original, the end is thicker and ensures increased operating efficiency.

Suitable for vehicles with small bushings, diameter 92 mm:

- Golf3 saloon, estate, cabriolet, Vento
Including automatic & Syncro (4 x 4):
2.0 8S (2E), 2.0 16S (ABF) 92->
2.8 VR6 (AAA), 2.9 VR6 (ABV) 92->
All enginesfrom 08/94->:
(fromchassis no. SW062 539-> or no. SB019 476->)

-Golf 4 cabriolet 06/98 ->06/02 (chassis from Golf 3 !!!)
All engines, Including automatic

- Corrado
2.9 VR6 (ABV)from 92->(chassis no. N-000 001->)
2.0 8S (2E / ADY), 2.0 16S (9A) from 95->
(from chassisno. S-000 052->)

- Caddy 2 96 ->03 all models
- Polo Classicsaloon 96 ->00
- PoloClassic estate 96 ->99 (up to chassis no. ->X-610 000)

1 flange + 1 reinforced bearing, for one side, left or right-hand.
For vehicles with small cups diameter 92 mm.

These partsoffer better quality than the original parts,
design defects have been corrected for
longer durability and better efficiency in operation.

Suitable for Passat 3 Saloon & Estate 92 ->97
including Automatic &Syncro (4 x 4):
- 2.8 VR6 (AAA) since 06/92->
- 2.9 VR6 (ABV) since 06/92->
- All engines since 93-> (chassis no. P-026 436->)

Rolling bearing,

For Roadster (E85):
- 2.0 i N46
- 2.2 i M54
- 2.5 i M54
- 2.5 i N52
- 2.5 si N52
- 3.0 i M54
- 3.0 si N52

For Coupé (E86):
- 3.0 if N52

FEBI brand front right or left front suspension upper bearing for BMW series 3 E36 :

Sedan :
- 316i and 318i M40 / M43
- 318is M42 / M44
- 318tds
- 320i M50 from 06/1992
- 320i M52
- 323i
- 325i from 06/1992
- 325td from 06/1992
- 325tds
- 328i

Compact and Touring :
- All models

Coupé :
- 316i
- 318is M42 / M44
- 320i M50 from 06/1992
- 320i M52
- 323i
- 325i from 06/1992
- 328i

Convertible :
- All models (except M3 3.0 S50 and 3.2 S50)

Quantity required per vehicle = 2
Sold individually

For Z3 (E36) Coupé:
- 2.8 M52
- 3.0 i M54

For Z3 (E36) Roadster:
- 1.8 / 1.9 M43
- 1.9 M44
- 2.0 M52
- 2.2 i M54
- 2.8 M52
- 3.0 i M54

Bushes only, without bearings, Powerflex polyurethane version for greater front axle precision.

Compatible with Volkswagen Golf 4 Saloon, Estate, Bora, New Beetle and Audi A3 type 8P

Sold by the pair for the 2 front shock absorbers.

For E28 :
- All models including M5

For E30 since 1982 ->1991 :
- All models including M3 (except 325 ix)

Front upper suspension bearing for Bmw z1 :
Bmw z1 E30 Roadster :
- 2.5i 6cyl 170hp from 07/1988 to 06/1991 (engine code m20b25)
Center diameter for shock absorber rod: 14 mm
Sold individually

Upper front suspensionbearing for Bmw 6 Series:
Bmw E24 :
- 628 csi 184hp from 05/1982 to 05/1987 (engine code m30)- 635 csi 218hp from 05/1982 to 04/1989 (engine code m30)- M635 csi 286hp from 10/1983 to 02/1989 (engine code s38)- M6 260hp from 07/1986 to 09/1988 (engine code s38)
To know :
- Center diameter for 14 mm shock absorber rod.
- Sold individually.

Front upper suspension bearing for BMW 5 series E34:

Sedan :
- 518i M40 and M43
- 520i M20 and M50
- 525td / tds from 09/1992

Touring :
- 518i / g M40 and M43
- 520i
- 525td

Center diameter for shock absorber rod: 14 mm

WARNING: Not suitable for E34 Sport M chassis!

Sold individually

Front suspension bearing MEYLE HD. Left ou right, each.

For VW Transporter T5, Multivan
included 4-Motion (4 x 4) version
Years : 04/2003->

Front suspension bearing MEYLE HD. Left ou right, each.

For VW Transporter T6, Multivan
included 4-Motion (4 x 4) version

Front left or right upper suspension bearing with FEBI bearing for BMW X3 E83 and LCI :

BMW X3 E83 :

- 2.0i 4cyl 150hp from 05/2003 to 07/2006 (engine code N46B20)
- 2.5i 6cyl 192hp from 02/2003 to 07/2006 (engine code M54B25)
- 3.0i 6cyl 231hp from 01/2003 to 07/2006 (engine code M54B30)
- 2.0d 4cyl 150hp from 05/2003 to 07/2006 (engine code M47D20TU)
- 3.0d 6cyl 204hp from 01/2003 to 08/2005 (engine code M57D30TU)
- 3.0d 6cyl 218hp from 03/2005 to 07/2006 (engine code M57D30TU)

BMW X3 E83 LCI :

- 2.0i 4cyl 150hp from 03/2006 to 06/2008 (engine code N46B20)
- xDrive20i 4cyl 150hp from 07/2008 to 08/2010 (engine code N46B20)
- 2.5si 6cyl 218hp from 03/2006 to 06/2008 (engine code N52B25)
- xDrive25i 6cyl 218hp from 07/2008 to 08/2010 (engine code N52B25)
- 3.0si 6cyl 272hp from 02/2006 to 06/2008 (engine code N52B30)
- xDrive30i 6cyl 272hp from 07/2008 to 08/2010 (engine code N52B30)
- xDrive18d 4cyl 2.0L 143hp from 04/2009 to 08/2010 (engine code N47D20)
- 2.0d 4cyl 150hp from 03/2006 to 08/2007 (engine code M47D20TU)
- 2.0d 4cyl 177hp from 03/2007 to 06/2008 (engine code N47D20)
- xDrive20d 4cyl 177hp from 07/2008 to 08/2010 (engine code N47D20)
- 3.0d 6cyl 218hp from 03/2006 to 06/2008 (engine code M57D30TU)
- xDrive30d 6cyl 218hp from 07/2008 to 08/2010 (engine code M57D30TU)
- 3.0sd 6cyl 286hp from 03/2006 to 06/2008 (engine code M57D30TU2TOP) --> bi-turbo
- xDrive35d 6cyl 3.0L 286hp from 07/2008 to 08/2010 (engine code M57D30TU2TOP) --> bi-turbo 3.0d engine


This high-quality suspension cup offers optimized quality compared to the original, with design flaws corrected for longer life and improved operating efficiency.

This product is sold individually.

Front suspension upper bearing with FEBI brand bearing for BMW series 3 E46 and series 5 E39:

E46 Sedan, Touring, Compact, Coupé and Cabriolet:
- All models until 10/2003 (except M3)

E39 Saloon and Touring:
- 520i, 523i and 528i from 09/1997
- 525i and 530 i (except EDC controlled suspension)
- 520d, 525td and 525tds from 09/1997
- 525d and 530d (except EDC controlled suspension)

This shock absorber upper stop suitable for right passenger or left driver side includes the ball bearing.

This high quality suspension cup offers optimized quality compared to the original, design flaws are corrected for better life and operating efficiency.

This product is sold individually.