Wheel and hub tool

This TOOLATELIER tool kit enables theremoval and fitting of wheel bearings.
This kit can be used for various makes of vehicle.

What's the material?
Thisextractor set is made of forged and hardened carbon steel.

What's in the set?
It comes with 9 bearing compression plates, outside diameters: 55.5, 59, 62, 65, 66, 71.5, 73, 78 and 84 mm
1 x extraction shaft
3 x extraction bell :
- outer Ø: 76 mm, 86 mm and 91 mm
- inner Ø: 70 mm, 76 mm and 82 mm

Various clamping screws
Hub screws: M12 x 1.5 and M14 x 1.5mm


Supplied in rigid case

These TOOLATELIER brand inertia bearing pullers, also known as bearing extractors , have an internal grip. They are used in automotive, motorcycle and industrial applications.

This set of tools is highly resistant to shocks, as well as to screwing and unscrewing.

Adapter sizes (min - max) :
- 8 - 11 mm
- 12 - 17 mm
- 18 - 23 mm
- 24 - 29 mm
- 30 - 34 mm

- Inertia weight with 24 cm rod
- Support beam, threaded rod: 13.5 cm

These extractors are used for bearings installed in blind holes.

Very often used for gearboxes, etc.

The inertia weight has a length of 290 mm with a double claw extractor with rod.

The sockets fit bearings with internal diameters from 5 to 52 mm.

This socket is useful for front wheel bearings on Suzuki Jimny models.

Square drive: 1/2"
Material: steel

This tool, also called a "valve opener" enables you to fit and remove your wheel valves.

Hook like the one originally provided with VWs

Multi-purpose white pen for:
- making repairs (distribution...)
- marking tyres

This wrench can be used to tighten motorcycle spokes.
It features 4 notches of 6.3 / 5.6 / 5.0 / 4.5 mm to accommodate a wide range of spokes.

BGS tyre-changer set :
Contents:
- 1 tire lever 300 mm- 1 tire lever 350 mm- 1 tyre-changer 380 mm

What is the purpose of adjustment control plates?

They are measuring tools for checking the toe-in, toe-out and complete locking of a car's wheels.

The plates are locked in place with pins.
Turntable diameter 335 mm,
Angle: / - 45 degrees.
2000 kgs maximum load per pair.

For use with ref :UO09099

Ideal for holding a wheel hub with 4, 5, 6 and 8 studs.

Can also be used with a pry bar, 1/2" square head

Very practical to immobilise the rear hub on vehicles equipped with a rigid axle differential.

This yellow marker can be used on metals, rubbers and glass parts.

Can be used on wet or dry surfaces.

This type of socket is intended for vans & HGVs. Very useful for taking off the special stud between twin wheels.

The twin wheel stud system design allows the inner wheel to remain stationary when removing the outer wheel.

Length: 90mm
Square drive: 3/4"
Material: chromium molybdenum with phosphate finish
- Profile: square 21mm

Applications: Mitsubishi Fuso, Hino, Isuzu, etc.

- prevents rim damage when mounting tires
- suitable for motocycle and car rims
- with cord against loss

This set of pullers will allow you to easily remove your brake drums, wheel hubs, universal joints and the drive shaft.

Suitable for hubs with 3, 4, 5, and 6 holes

Supplied with washers of different thicknesses for attachment on most vehicles.

To write on, or mark your tyres.
Makes marking your tyres easier (to identify you summer/winter tyres), highlights the letters written on the sidewalls and is resistant to water and adverse weather.

Socket for extracting interior drive shaft screws, for the Volkswagen Transporter T4 and Touareg.

Size: 12 mm x 800 mm
Square drive: 1/2

Dimensions: 650 x 28 x 9 mm

This hub extractor has 4 and 5 hole centers.

Wheel bolt sizes are M12 and center distances range from 100 to 115 mm.

Set of balancing weights for sheet steel rims.

Sizes:

- 5 x 5, 10, 15, 20g
- 3 x 25, 30g
- 2 x 35, 40, 45, 50, 55g