Fuel pump

Full kit

Voltage: 12 volts
Flowrate: 113 l/h
Pressure: 280/350 g
Femalethread: 1/8" x 27 NPTF
Male diameter: 8 mm
Weight: 700 g

Facet pumps run on 12 volts (3/4 amps),
They are self-adjusting, sealedandlight, with integral filter (except on transistors).

Essential for any twin-carburettor assembly
Pressure: 0,42 bar
Max. flow: approximately 114 L/H
Universal fitting: 12 volts
Soldwith two unions: 8 mm

Full kit

Voltage: 12 volts
Flowrate: 152 l/h
Pressure: 450/500 g
Female thread:1/4" x 18 NPTF
Malediameter: 9 mm
Weight: 750 g

Facet pumpsrun on 12 volts (3/4 Amps),
They are self-adjusting, sealed and light,with integral filter (except on transistors).

FACET low-pressure electric fuel pump for mounting at pressures from 4 to 7PSI (0.27 to 0.48 bar) for a maximum flow rate of 132.5 L/H.

A Filter King is recommended to regulate and save fuel.

Pressure: 4 - 7 Psi (0.27 to 0.48 bar)
Max. flow: 132.5 L/H
Universal mounting: 12 Volt
Inlet / outlet diameter: 8 mm
Anti-corrosion surface treatment
Made in the USA.
Supplied with mounting bracket, fitting and pre-filter.

For use on Cox

Low-pressure, self-regulating, electric rotary petrol pump.

Extremely quiet
Body diameter: 38 mm
Pressure: 0.27 to 0.38 bar (4 to 5.5 psi)
Max. flow rate: 95 l/h
Gravity-operated, pushes gasoline but does not suck it up.

Can be mounted on 6V, in which case flow rate will be lower.

Fullkit

Voltage: 12 volts
Flowrate: 132 l/h
Pressure: 450/500 g
Female thread: 1/8" x 27 NPTF
Male diameter: 8 mm
Weight: 750 g

Facet pumps run on 12 volts (3/4 amps),
They are self-adjusting, sealedand light, with integral filter (except on transistors).

Rod metal / hexagonal rubber universal with double threaded 6 mm.
Support for maintainingand fixing an electric fuel pump, a horn, an exhaust pipe ... avoid resonance vibrations in the body and chassis.

Total height, rubber + rods : 35 mm
Rubber silentblock height : 15 mm
Rubber silentblock width : 19mm
Thread length : 10 mm
Thread diameter : 6 mm

Electric fuel pump compatible with carburator mounts. This low pressure compact and quiet pumpis manufactured by American specialist Edelbrock.
As its operating pressure is between 4 and 7 PSI (0.27 - 0.48 bar), it thus offers a flow rate of about 144 L/H.
The pump comes with a screw-in fuel filter at the pump inlet

A push type, it mounts near the tank,in a horizontal position, rather than near the carbs. This fuel pump "pushes" the fuel, so it is not suction.
It is also compatible with E85 Ethanol

The ideal pump to use with one or more Weber!!

Dimensions:
- Length: 184mm with filter
- Width (including bracket) 80 mm
- Mounting center distance: 60 mm
- Fittings: 8mm

Pressure: 1.5 - 4 Psi / 0.10 - 0.28 Bar
Weight: 350 g
Decibels: 65 dB
Voltage: 12 Volts
Connector: 1/8 NPTF
Length: 85mm
Height: 60 mm
Lifespan: 6,000 hours
Made in the USA.
Supplied with mount, connector and pre-filter.
Works by gravity, pumps the fuelout but does not draw it in.

Choose the benchmark in electric fuel pumps by opting for FACET quality!
For optimum performance, we recommend using a Filter King to regulate and save fuel.

Pressure: 0.10 to 0.28 Bars (1.5 to 4 PSI)
Max flow: 105.9 L /H
Universal mounting: 12 Volt
Anti-corrosion surface treatment
Made in the USA.
Supplied without fittings (order Ref: VC43504).

Tip: Pump to be installed on silentblocs to filter operating noise, lower than the tank as it works by gravity (pushes gasoline at low pressure but does not suck it in).

Electric fuel pump compatible with carburator mounts. This low pressure compact and quiet pump ismanufactured by American specialist Edelbrock.
As its operating pressure is between 2 and 3.5 PSI(0.14 - 0.24 bar), it thus offers a flow rate of approximately 113 L/H.
The pump comes with a screw-in fuel filter at the pump inlet

Push type, it mounts near the tank,in a horizontal position, rather than near the carbs. This fuel pump "pushes" the fuel, so it is not suction.
It is also compatible with E85 Ethanol

The ideal pump to use with one or more Weber!!

Dimensions:
- Length: 184mm with filter
- Width (including bracket) 80 mm
- Mounting center distance: 60 mm
- Fittings: 8mm

Metal rod / universalround rubber, with doble thread 6 mm.
Supports and fix an electric fuelpump, a horn, an exhaust tube...
avoid resonance vibrations in the bodywork and chassis.

Total height, rubber + rods : 43 mm
Rubber silentblock height : 15 mm
Rubber silentblock width : 27 mm
Tread length : 14 mm
Thread diameter : 6 mm

Contents:
- 2 rubber silentblocs with thread
- 1 cable for grounding

Spare filter for the following petrol pumps:
- UC43510
- UC43508
- UC43506

Connections between fuel pump and fuel hose

Diameter: 8 mm

2 connections between fuel pump and fuel hose

Diameter: 6 mm

FACET Posi-Flo silent petrol pump

Pressure: 4 - 7 Psi / 0.28 - 0.48 bar
Weight : 350 gr
Decibel : 65 dB
Voltage : 12 Volts
Connection : 1/8 NPTF
Flow rate: 120L/hour
Length: 85 mm
Height: 60 mm
Service life: 6000 hours
Made in the USA.
Supplied with attachment, connection and pre-filter.
Gravity-operated, pushes gasoline but does not suck it up.

Contains:

1 mounting bracket - diameter: 60 mm
1 mounting kit
1 foam strip

Mounted by 2 screws

This fuel pump for Dyane - 6V is a quality reproduction.

This Dyane fuel pump is specific to early 6V models with a top-mounted inlet. It comes with 2 base gaskets, and has no priming lever.

We strongly recommend fitting a thermal shim to isolate the pump from the engine crankcase.

compatible models :

- DYANE (425) type AYA: 08/1967 to 01/1969
- DYANE 4 type AYA2: 03/1968 to 02/1970

Immersed pump for the fuel tank, ideal for significant engine tuning thanks to a maximum flow rate of 516l/h and the compatibility with E10 and E85 fuel.
To be adapted on your vehicle to replace the original petrol pump