Diagnostic and purging tool

This TOOLATELIER manual brake bleeder is designed for use with most master cylinder reservoirs.

Once this bleeder is connected, fill the canister with fluid and pressurize the circuit by pumping. You can then carry out the bleeding operation without external assistance.
Reservoir capacity: 2 liters.

Int. cap diameter: 42.24 mm for 43 mm expansion vessel.

Supplied with European adapter.

This tool allows a person to easily bleed the brake system and clutch circuit unaided.

Air pressure: 6 to 12 bars
Size: (W) 225 mm x (L) 135 mm x (H) 192 mm

This brake pressure testerenables to control the state andefficacity of your brake circuit by pressure.
The different connexionadaptators have to be placed on the brake caliper, or on the wheel cylinder atthe drain screw for a drum brakes.

It has two manometers with a measure range from 0 to 250 kg/cm2 and 22 connexion adaptators.

Beforeeach utilisation, it's better to refer to the technical revue of the constructor.

This TOOLATELIER auto bleeder for hydraulic systems is ideal for quick and easy replacement of used brake orclutch fluid without the help of a third party.

This brake fluid bleeder consists of a reservoir that holds the new fluid, a hose with a cap that fits over the brake fluid reservoir (master cylinder), and a hose that connects to the spare wheel valve. All you have to do is position yourself at the bleed screws on the caliper or wheel cylinders, which are opposite the master cylinder, then move progressively closer to the latter (bleed screw furthest from the master cylinder to the nearest). The fluid is changed and the air bubbles disappear = better braking = greater SAFETY for you and your loved ones.

This practical system makes it easy to replace old fluid with new, under pressure.

Several adapters are supplied with the tool for vehicles equipped with variable-cap brake fluid reservoirs.

Contents :

- 1 bottle max. 1.4 bar to prevent leaks!
- 3 hoses 3.5 x 303 mm, 5.4 x 303 mm, 5.4 x 183 mm
- 25 mm cap and seal for Lockheed systems
- 27 mm cap and seal for VAG systems
- 44/45 mm cap and 2 seals for Girling and all ATE systems
- 46 mm cap and gasket for Girling systems

Display with 4 LEDs for quick and easy reading of the brake fluid status.

Battery 9V, 6F22 or equivalent.

A signal sounds when the battery is discharged.

Ideal for bleeding brakes and clutches via the bleed nipple.
Can also be used to transfer brake fluid from the holding bottle to difficult to reach master cylinders for example as found on late model (2007) Ford C-Max and the rear master cylinder on the Triumph 1050 Sprint ST motorcycle.

Quick and easy to use.
Quick and easy to use.
Instructions provided.

Identify percentage of water in brake fluid.
Suitable for Dot 3, Dot 4, Dot 5
Quick and simple tool with battery
Colour coded LEDs show level of water.
Colour coded LEDs show level of water.
Not suitable for silicone based Dot 5.1

The principle of this brake bleeder hose is simple: the valve opens and closes automatically as a function of the pressure exerted on the brake pedal.

This non-return valve prevents air from being sucked in, so you can bleed without the help of a second person.

This professional tool is suitable for most scooters, motorcycles, quads and cars.

Ideal for bleeding motorcycle brake and clutch systems.

Supplied with 3 adapters and a magnet for chassis mounting.

This adapter can be used with the bleeder reference TA00021 or equivalent.

It is used to bleed calipers fixed to several pistons equipped with 2 bleed screws.

Length of silicon pipes 1060 mm x 2 and 100 mm x 1
Pipe diameters: inner 3 mm and outer 7 mm

This FACOM brake and clutch bleeder is specifically designed for intensive use in automotive environments.

This analogue system has a 10l reservoir as well as storage for all accessories.

Its operation is very simple, just plug it in with a 12V battery and you're done!
The pressure can be adjusted by means of a knob. For added safety, there is an automatic "low level" stop gauge.

The pressure is regulated and adjustable from 0.5 to 4 bars.
Its weight, 16.2 kg

3 years warranty

This adapter allows you to use the automatic bleeder ref.: TA00378 / TA00390 or equivalent on awider range of vehicles.

This "plug" can therefore be used on all brake fluid reservoirs with any shape that have a filler cap size between 21and 90 mm.

Product benefits:

- Retaining hook
- Specific plastic to see the brake fluid
- Capacity of 1500 ml
- Graduations by 100 ml
- Can be adapted to universal bleeders

Ideal MOT tool.
Allows engine speed to be set, checking emissions.
Selected steel.
One man operation.
One man operation.
Time saver.

Replacement plug for TA00378 steam trap.

Int. diameter: 44 mm
Outside diameter: 53 mm
Orifice diameter under cap : 4 mm