Holder

Flange screw6x16 multi-purpose #4 for MX5 NA

Flange screw 6x16 multi-purpose

Product Properties:

- Used for attaching many parts: air filter, radiator, fuel tank, trunk, body parts, dashboard, windshield washer jar, etc
- Genuine MAZDA part
Suitable for all models of Mazda MX-5 NA

Inner wheel arch clip for Mazda MX-5 NA

For MX-5 NA all models

Although very practical, the original clips are fragile when removed. They must be carefully unscrewed before being pulled out.
It is not uncommon for these clips to break on removal.
For mounting, push the unscrewed clip into the mounting hole and only then screw in the middle.

Sold individually

A plastic clip for attaching bodywork trim / trim strips.
Sold individually, 40-50 required per vehicle.

- For VW Beetle

Plastic clip for Citroën ID door panel trim.
Attached to the top of the panel on some Citroën ID models, there are 4 clips per panel.
Compatible with all Citroën ID models.

This upper trunk seal clip secures the upper trunk seal at the junction with the rear window of your Citroën ID. It guarantees a reliable seal and a good seal, preventing water infiltration into the trunk.
This clip holds the rubber to the top edge of the trunk lid, where it rests on the rear window.
Compatible with all models.

This upper trunk seal clip secures the upper trunk seal at the junction with the rear window of your Citroën DS. It guarantees a reliable seal and a good seal, preventing water infiltration into the trunk.
This clip holds the rubber to the top edge of the trunk lid, where it rests on the rear window.
Compatible with all models.

Rivet clip "Push" FORST for Volkswagen dashboard
Rivet clip consisting of 2 interlocking parts with retaining system, used for many Volkswagen applications, e.g. : - Glove box retainer on VW Golf 2 - Fuse holder on VW Corrado - Dashboard mounting on Transporter T4
Sold individually

A rubber cap for mounting wide body mouldings.
For bodywork holes with 7mm diameter.
Sold individually, 40 to 50 pieces needed for one vehicle.

Please check if your holes measure 6 or 7mm!

For VW Beetle

Set of 475 clips also called staples for vehicles from the Mazda group. They are used to secure door panels, locks, seals, mud flaps, bumpers, etc.

OEM references for clips: 2042301 / 992780404 / 992780405 / 999100402 / 9046709139 / 6508197AA / 99249051B / 992640543A / 992640543A / B0016830200 / B09251833 / B1016825200 / B45556741 / BC1DSA145 / BF6750033 / BF8250233 / G03158762 / N30413356A

This screw cover for Corrado and Golf 3 and 4 Cabriolet - 3D is a 3D-printed part.

This screw cover for Golf 3, 4 and Corrado faithfully reproduces the original VW part. Extremely faithful reproduction made in ABS.
This remanufactured part was produced exclusively for MECATECHNIC using the 3D printing process by a French company specializing in the reproduction of rare or missing parts. This piece has been finished to perfectly reproduce the original grain.

Plastic clip for Citroën DS door panel trim.
Attached to the top of the panel on some Citroën DS models, there are 4 clips per panel.
Compatible with all Citroën DS models.

This stainless steel door panel clip for Citroën DS is located at the front of the panel and holds it in place.
It is used on most Citroën DS models.
Compatible with the following types:DX-DJ-DY-PA typetype BK except commercial.

These upholstery staples - x200 are required for finishing the seat covers.

These upholstery staples sold in packs of 200 are compatible with the seat trims of all 2cv cars and derivatives.
Fitting these upholstery staples, known as "pignose staples", requires special pliers.

This upholstery staples and hooks kit for 2cv cars and derivatives enables you to fit 2 individual seats.

Including 60 classic staples and 14 trim tensioning hooks, this set enables you you to fit 2 seat trims.
Use the staples to tighten the wings and flaps on the upholstery and the hooks to finish tensioning the connecting strip between the seat and back.

These upholstery staples - x200 for DYANEs and Acadianes are necessary to finish the seat covers.

These upholstery staples sold in packs of 200 are compatible with the seat trims of all 2cv cars and derivatives.
Fitting these upholstery staples, known as "pignose staples", requires special pliers.

6 door panel clips for Porsche 911 type F and G from 1965 to 1989 :

- Porsche 911 type F :

- 911 2.0 from 1965 to 1967
- 911 2.0 S from 1967
- 911 2.0 T / L / S from 1968
- 911 2.0 T / E / S from 1969
- 911 2.2 T / E / S from 1970 to 1971
- 911 2.4 T / E / S from 1972 to 1973
- 911 2.7 Carrera RS from 1973

- Porsche 911 type G :

- 911 2.7 from 1974 to 1977
- 911 S 2.7 from 1974 to 1977
- 911 Carrera 2.7 from 1974 to 1976
- 911 Carrera 3.0 from 1976 to 1977
- 911 SC 3.0 from 1978 to 1983
- 911 Carrera 3.2 from 1984 to 1989

- 911 Turbo 3.0 from 1975 to 1977
- 911 Turbo 3.3 from 1978 to 1989

Round plastic clip for bodywork 4 x 12 mm for fixing (depending on model):
- Acronyms for car
- Radiator grille
- Wings
- Wing extension
- Mudguard
- Grille car

ForGolf1 Berline, Cabriolet & Caddy.

Pivot for mounting sound deadening, protective housing or engine fairing for VW Transporter T25 from 05/1979 to 07/1992 :- 1.6 Diesel 50hp (CS)- 1.6 turbo-Diesel 70hp (JX)- 1.7 Diesel 57hp (KY)

For Golf 1:
- Berline, Cabriolet & Caddy.