Measuring tool

0

Multimeter for automotive use, for 2 and 4-stroke engines.

Technical information :
USB port for PC connection : yes
Data retention function (saves the measured value): yes
Overload indicator: yes
Low battery indicator: yes

Measurement range:
DC Voltage: 6 / 60 / 600 / 1000 V
Alternating voltage: 6 / 60 / 600 / 1000 V
Continuous current: 60 mA / 600 mA /6A / 20A
Alternating current: 60 mA / 600 mA / 6A / 20A
Resistance: 600 Ohm / 6 kOhm / 600 KOhm / 6 MOhm / 60 MOhm
Continuity: audible signal sounds at below 20 ohms
Diode: test current approx. 0.8 mA
Capacity: 40nF to 4000uF
Temperature: -20°C to 400°C
Frequency: 10 Hz to 10 MHz
Lifecycle: from 0.5% to 99.9%
Tachometer: 120 to 20,000 rpm
Dwell : (0-90°) / (0-72°) / (0-60°) / (0-45°)
Pulse width from 0.5 ms to 20ms
Includes: temperature sensor, condenser adapter, inductive pick-up, 2 measurement cables, USB cable CD with driver / software, bag and 9V battery

Ideal for measuring valve clearances on models with 8 mm valves.
Supplied with a closing and opening shim.
Size : 8 mmWeight : 0.03 kgHeight : 140 mmWidth : 100 mmDepth : 22 mm
Equivalent to original part numbers : 0000.44119, 0000.44120 and 887651322

- for fault diagnosis of 12V battery and charging systems
- easy to use, just connect and check indicator lights
- LED's are electronically controlled
- 3 LED's for battery test:
- LED red = battery empty or defective
LED yellow = battery OK
LED green = battery very good
- 3 more LED's for alternator test:
LED green = charging system OK
LED yellow = charging system OK
(maximum charging voltage)
LED red = charging system is not OK
(it may damage the battery
and other parts of the electric system)

- allows stippling of insulated cords

This caliper will enable you to take interior and exterior measurements, but can also be used as a depth gauge. It is made of chrome-plated material and has a measuring range of 0-200 mm.

Supplied in a protective case.

Ideal for measuring valve clearances on models with 7 mm valves.

Delivered with a closing and opening pin.

Size: Ø 7 mm
Weight: 0.03 kg
Height: 140 mm
Width: 100 mm
Depth: 22 mm

- rust-proof
- 0,08 - 0,10 - 0,12- 0,13 - 0,14 - 0,15 - 0,16 -
0,18 - 0,19 - 0,20 - 0,25 - 0,26 Inch
- 0,203 - 0,254 - 0,305- 0,330 - 0,356 - 0,381 - 0,406 -
0,457 - 0,483 - 0,508 - 0,635 - 0,660 mm

BGS measuringcables and test probes :
- Suitable for automotive measurements up to 30 volts.
Kit contents:
- 5 alligator clips, 4 mm socket, red, black, yellow, green, blue- 5 test needles, straight design, 4 mm socket, red, black, yellow, green, blue- 5 test needles, 45° bent, 4 mm barrel, red, black, yellow, green, blue- 5 test needles, 90° bent 4 mm sleeve, red, black, yellow, green, blue- 5 test probes (cable perforation), 4 mm socket, red, black, yellow, green, blue- 5 measuring cables with 4 mm male plug on alligator clip, length 104 cm, red, black, yellow, green, blue

Application : All modern 6 speed Ducati's equipped with a dry clutch.
Made from composite material.
Supplied witha bolt which can be located in the bolt location after removing the clutchcover.
Motorcycle must be locked in gear with back wheel locked
Motorcycle mustbe locked in gear with back wheel locked
Essential tool.

- measures the coating thickness on ironmetal and non-iron-metal
- digital display with backlight
- one-hand operation
- measuring range: 0 - 40 mils/ 0 - 1000 µm
- resolution : 0,1 mils / 0,1 µm
- accuracy:
+/- 4 dgts (0 - 7,8 mils)
+/- 10 dgts (0 - 199 µm)
- response time: 1 sec
- auto hold function
- automatic turn-off

delivered with bag, battery, calibration pad & manual

0

Very practical for connecting to TPS/MAP sensors, injector, etc.

Test-lead point contents: 2 yellow, 2 green, 2 red, 2 blue

Product benefits:

- Resistant to automobile solvents
- Slightly flexible test-lead points

- handy pocket-size Digital Multimeter
- with LCD display
- diagnosis in the automotive, motorcycle and home use
- with important measurement areas such as:
- voltage (AC) up to 500 V
200V and 750V ranges
- voltage (DC) up to 500V
ranges 200mV, 2000mV, 20V, 200V, 500V
- direct current (DC A) 0,2 mA, 2 mA, 20mA, 200mA, 5A
- resistance 200Ohm, 2000Ohm,20 kOhm,
200kOhm, 2000kOhm
- dimensions: 125 x 69 x 25 mm

The precision of the angles of measurement on new engines is vital. The inclinometer enables you to measure angles such as the castor, camber or others.

This tool is also used to adjust the valve opening controls in models of the PSA group (manufacturer code 1376-A).

Power source: one 1.5 V AAA battery

This FACOM brand multimeter diagnostic accessory set is ideal for circuits under 49 volts.

Contents :

- 2 test leads
- 2 needles
- 2 Pic probes
- 1 needle storage tube
- 1 storage pouch

Digital tire pressure gauge from 0.35 to 7 bar
Measurement units: bar, psi, kPa, kg/cm2
Tolerance: /- 1 psi / 0.07 bar

Made from aluminium.
Identifies bolts | pipe threads and spark plugs 10-18mm.
US or metric sizes.
Range 5/16" to 3/4", 10tpi to 44tpi, metric thread sizes 2.5 to 22mm and pitch of 0.45mm to 2.5mm.
Range 5/16" to 3/4", 10tpi to 44tpi, metric thread sizes 2.5 to 22mm and pitch of 0.45mm to 2.5mm.
Fast accurate.

This caliper will enable you to take interior and exterior measurements, but can also be used as a depth gauge. It is made of chrome-plated material and has a measuring range of 0-150 mm / 1/20th.

Supplied in a protective case.