Elements of hanging pots

This suspension clevis knife edge for 2cvs before 1970 - Big is a quality reproduction.

This large knife edge locks the rear tie rod ends on the suspension cylinders to the suspension arms.

You will need one per side with its own 2 new pins.

This suspension adjuster for 2cvs before 1970 - 110mm exhaust is a quality reproduction.

This small suspension cylinder adjustor is made of high quality steel. It comes without the nuts.

Please note! it is not compatible with derivatives with a 130 mm diameter suspension cylinder.

This suspension cylinder stop for 2cv vans from 1955 to 1963 - AK350-400 - 110mm exhaust is a quality remanufacture.
Small diameter rubber suspension cylinder bump stop mounted on its own bichromate steel base.
It is compatible with the 110 mm diameter suspension cylinders on Méharis, 2cvs and Dyanes saloon cars and should be positioned on each side of the suspension cylinder to reduce the impact of too much travel and avoid damaging the filled cups.

This suspension rod end for 2cv vans is superior quality.
This cast iron tie rod clevis is faithful to the original, and connects the suspension cylinders to the front and rear suspension arms and holds the locking knife edges.
The thread enables you to adjust the saloon's trim from 1971 onwards.

This suspension rod end for AMI6 and AMI8 cars is high quality.
This cast iron tie rod clevis is faithful to the original, and connects the suspension cylinders to the front and rear suspension arms and holds the locking knife edges.
The thread enables you to adjust the attitude.

This front suspension tie rod for 2cv vans - 590mm is faithful to the original.
It is compatible with all models.

This suspension pot cup for Mehari 4x4 (06/1979-06/1983) - 130mm is a quality reproduction.

This suspension pot cup for mehari 4x4 is compatible with all 130mm "big pot" models.

Compatible models:
- Mehari 4x4 type AY-CE: 06/1979 to 06/1983

This ringed suspension cylinder cup for 2cvs before 1970 - 110mm exhaust is faithful to the original.

This ringed cup is the fitting that closes either end of small suspension cylinders.
It is welded to the ends of the housing to close it. Its inner diameter includes a brass ring that holds the threaded pipes.

This suspension rod end for Meharis is superior quality.
This cast iron tie rod clevis is faithful to the original, and connects the suspension cylinders to the front and rear suspension arms and holds the locking knife edges.
The thread enables you to adjust the saloon's trim from 1971 onwards.

This suspension cylinder end ring is for Mehari 4x4 - 130mm exhaust

It is compatible with all models of vans with large suspension cylinders.
Acadianes, all AMI6 and AMI8 cars, both saloon and estate models, but also with the Meharis 4x4.

This suspension adjuster for 2cv vans from 1955 to 1963 - 110mm exhaust is a quality reproduction.

This small suspension cylinder adjustor is made of high quality steel. It comes without the nuts.

Please note! it is not compatible with derivatives with a 130 mm diameter suspension cylinder.

This suspension cylinder stop for 2cvs before 1970 - 110mm exhaust is a quality remanufacture.
Small diameter rubber suspension cylinder bump stop mounted on its own bichromate steel base.
It is compatible with the 110 mm diameter suspension cylinders on Méharis, 2cvs and Dyanes saloon cars and should be positioned on each side of the suspension cylinder to reduce the impact of too much travel and avoid damaging the filled cups.

This suspension adjuster for Mehari - 110mm exhaust is a quality reproduction.

This small suspension cylinder adjustor is made of high quality steel. It comes without the nuts.

Please note! it is not compatible with derivatives with a 130 mm diameter suspension cylinder.

This suspension clevis knife edge for Meharis - Big is a quality reproduction.

This large knife edge locks the rear tie rod ends on the suspension cylinders to the suspension arms.

You will need one per side with its own 2 new pins.

This suspension clevis knife edge for 2cvs - Small is a quality reproduction.

This small knife edge locks the front tie rod ends on the suspension cylinders to the suspension arms.

You will need one per side with its own 2 new pins.

This suspension tie rod end adjuster nut for 2cvs - 46 mm is faithful to the original.

This M36 fine nut is made of chromated steel. You need 2 for each threaded pipe, i.e. 4 for each suspension cylinder.
It is only compatible with 110 mm suspension cylinder adjusters.

This ringed suspension cup for AK350-400, Acadiane and AMI - 130mm cup is a quality remanufacture.

This lined suspension pot cup for Acadiane (03/1978-03/1987) - 130mm is a quality reproduction.

This suspension pot cup for Acadiane is compatible with all 130mm "big pot" models.

Compatible models:
- Acadiane type AY-CD: 03/1978 to 03/1987

This suspension adjuster for Mehari 4x4 - 130mm exhaust is faithful to the original.

It is compatible with all models of vans with large suspension cylinders.
Acadianes, all AMI6 and AMI8 cars, both saloon and estate models, but also with the Meharis 4x4.

This ringed suspension cylinder cup for DYANEs - 110mm is faithful to the original.

This ringed cup is the fitting that closes either end of small suspension cylinders.
It is welded to the ends of the housing to close it. Its inner diameter includes a brass ring that holds the threaded pipes.