Shock absorber bearing

3RG front shock absorber bearing kit for Peugeot 205
For Peugeot 205 all modelsSedan and CabrioletGasoline, Diesel and 205 GTI
Front shock absorberbearing kit Left or right side
Screws not supplied

Bearings with polyurethane bushes, enables better rear axle guidance and prolonged durability:

For E36 Saloon, Touring, Coupé and Compact:
- All models except M3

For E46 Saloon, Touring, Coupé and Compact:
- All models except M3
(Not suitable for E46 Convertible and E46 Coupé - there is another fitment with a 12 mm bearing)

Reinforced upper rear suspensionbearing , brand MEYLE HD range, right passenger side or left driver side for BMW 3 Series E30 with standard chassis or M-Technic chassis:

Sedan, Coupé and Touring:
- All petrol and diesel models from 12/1981 to 02/1994 (including 325ix 4-wheel drive and M3).

Cabriolet :
- 318i 115hp from 07/1990 to 04/1993 (engine code M40B18)
- 320i 6cyl 129hp from 04/1986 to 09/1990 (engine code M20B20)
- 320i 6cyl 129hp from 10/1990 to 01/1993 (engine code M20B20)

ATTENTION: Not suitable for Cabriolet 325i!

Suitable for 10mm diameter shock absorber rod.
Supplied with gasket.
Conical washer and nuts not supplied.

This high-quality rear suspension cup offers optimized performance compared with the original version: design faults are corrected, and the materials used provide greater strength, longer life and improved operating efficiency.

WARNING: When replacing your bearings, it is imperative to replace and reinstall the conical washer underneath each one (see photo). Otherwise, the bearing silentblocks will come out of their housings and the shock absorbers will pass "through" the body, which could cause serious damage to your vehicle.

This product is sold individually.

Bottom diameter: 45mm
Height lower part: 23mm

Reinforced upper rear suspensionbearing , brand MEYLE HD range, right passenger side or left driver side for BMW Z3 E36 with standard chassis or M-Technic chassis:

Roadster :
- 1.8 4cyl 115hp phase 1 from 05/1997 to 09/1998 (engine code M43B18)
- 1.9 16V 4cyl 140hp phase 1 from 05/1997 to 04/1999 (engine code M44B19)
- 1.8 4cyl 1.9L 118hp phase 2 from 04/1999 to 08/2000 (engine code M43B19TU)
- 1.9i 4cyl 118hp phase 2 from 08/2000 to 06/2002 (engine code M43B19TU)
- 2.2i 170hp phase 2 from 12/1999 to 06/2002 (engine code M54B22)
- 2.8 192hp phase 1 from 05/1997 to 08/1998 (engine code M52B28)
- 2.8 192hp phase 1 from 09/1998 to 03/1999 (engine code M52B28TU)
- 2.8 193hp phase 2 from 04/1999 to 05/2000 (engine code M52B28TU)
- 3.0i 231hp phase 2 from 09/1999 to 06/2002 (engine code M54B30)
Coupé :
- 2.8 192hp phase 1 from 05/1997 to 08/1998 (engine code M52B28)
- 2.8 193hp phase 1 from 09/1998 to 03/1999 (engine code M52B28TU)
- 2.8 193hp phase 2 from 04/1999 to 05/2000 (engine code M52B28TU)
- 3.0i 231hp from 09/1999 to 06/2002 (engine code M54B30)

Suitable for 10mm diameter shock absorber rod.
Supplied with gasket.
Spacer washer and nuts not supplied.

This high-quality rear suspension cup offers optimized performance compared with the original version: design faults are corrected, and the materials used provide greater strength, longer life and improved operating efficiency.

WARNING: When replacing your bearings, it is imperative to replace and reinstall the spacer washer located under each one (see photo). Otherwise, the bearing silentblocks will come out of their housings and the shock absorbers will "pass through" the body, which could cause serious damage to your vehicle.

This product is sold individually.

Bottom diameter: 45mm
Height lower part: 23mm

Reinforced upper rear suspensionbearing , brand MEYLE HD range, right passenger side or left driver side for BMW 3 series E36 and E46:

E36 Sedan, Touring, Coupé, Cabriolet and Compact:
- All models with standard or M-Technic chassis from 11/1989 to 08/2000 (except M3)

E46 Sedan, Touring, Coupé and Compact :
- All models with standard or M-Technic chassis from 04/1997 to 07/2005 (except M3 and Cabriolet)

Suitable for 10mm diameter shock absorber rod.
Supplied with gasket.
Conical washer and nuts not supplied.

This high-quality rear suspension cup offers optimized performance compared with the original version: design faults are corrected, and the materials used provide greater strength, longer life and improved operating efficiency.

WARNING: When replacing your bearings, it is imperative to replace and reinstall the conical washer underneath each one (see photo). Otherwise, the bearing silentblocks will come out of their housings and the shock absorbers will pass "through" the body, which could cause serious damage to your vehicle.

This product is sold individually.

Bottom diameter: 45mm
Height lower part: 23mm

For Polo 6N2
- All models

For Polo Classic 6V2
- All models from 09/99->

For Polo 9N1:
- All models with standard chassis

For Polo 9N3 with standard chassis:
- 1.2 54hp and 60hp (BMD, BBM)
- 1.2 64hp and 70hp (BME, BZG)
- 1.4 TDi 68hp, 70hp and 80hp (BNM, BWB, BMS, BNV)
- 1.4 75hp, 80hp and 85hp (BKY, BUD, AXU)
- 1.4 100hp (BBZ)
- 1.6 105hp (BTS)
- 1.9 SDi 64hp (ASY)
- 1.9 TDi 100/101hp (BMT, ATD, AXR)
- 1.9 TDi 130hp (ASZ, BLT)

Febi front suspension bearing for Bmw z1 :
Bmw z1 E30 Roadster :
- 2.5i 6cyl 170hp from 07/1988 to 06/1991 (engine code m20b25)
Central diameter for shock absorber rod: 14 mm
This cup , located on the frontshock absorber , is valid for the right-hand passenger side and the left-hand driver side.
If you hear noises when driving over bumps or holes, or if your cornering behavior deteriorates, these are signs that the upper bearings need changing.We also recommend replacing them when fitting new shock absorbers.
This product is sold individually.

Suspension bearing for left or front right shock absorber, comes on its own without a ball bearing.

Compatible with Seat Ibiza type 6K, all models from 03/1999->

Suspension bearing for left or front right shock absorber, comes on its own without a ball bearing.

Compatible with Seat Ibiza type 6L with standard chassis:
- 1.2 64hp (BME)
- 1.4 TDi 70hp (BNM)
- 1.4 TDi 80hp (BNV)
- 1.4 75hp (BBY, BKY)
- 1.4 100hp (BBZ)
- 1.6 100hp (BAH)
- 1.9 TDi 130hp (BLT)
- 2.0 115hp (BBX)

Suspension bearing for left or front right shock absorber, comes on its own without a ball bearing.

Compatible with Skoda Fabia type 6Y with standard chassis:
- 1.0 50hp (AQV, ARV)
- 1.2 54hp (AWY, BMD)
- 1.2 64hp (AZQ, BME)
- 1.4 60hp (AZE, AZF)
- 1.4 68hp (AME, AQW, ATZ)
- 1.4 TDi 70hp (BNM)
- 1.4 75hp (AUA, BBY, BKY)
- 1.4 TDi 75hp (AMF)
- 1.4 80hp (BUD)
- 1.4 TDi 80hp (BNV)
- 1.4 100hp (AUB, BBZ)
- 1.9 Diesel 64hp (ASY)
- 1.9 TDi 100hp (ATD, AXR)
- 1.9 TDi 130hp (ASZ, BLT)
- 2.0 115hp (AZL)

Upper front suspension bearing with ball bearing,

Compatible with Volkswagen Touran type 1T1, 1T2 all models from 02/2003 ->05/2010

For all Golf 5, Golf 5 plus and Golf 5 Variant

For Passat 5:
- saloon type 3B3 from chassis 3B-1-300001->
- estate type 3B6 all models

For Passat 4 (3B2, 3B5):
- 1.6 100hp (ADP, AHL, ANA, ARM)
- 1.8 115hp and 125hp (AFY, ADR, APT, ARG)
- 1.8 150hp (AEB, ANB, APU)
- 1.9 TDi 90hp and 100hp (AHH, AHU, AVB)
- 1.9 TDi 110hp (AFN, AVG)
- 1.9 TDi 115hp (AJM, ATJ)
- 2.5 TDi 150hp (AFB, AKN)
- 2.6 150hp (AGZ)
- 2.8 180hp and 190hp (AGE, ATX)
- 2.8 193hp (ACK, APR, AQD)

For Passat 5 (3B3) saloon only:
- All up to chassis ->3B-1-300000

Suitable for:
- Golf 5 / Golf 6
- Audi A3 8P (including Sportback and Cabriolet)
- Audi TT (8J)

Bushes only, without bearings, Powerflex polyurethane version for greater front axle precision.
This set enables the front of the vehicle to be lowered by 10 mm

Compatible with Volkswagen Golf 4 Saloon, Estate, Bora, New Beetle and Audi A3 type 8P

Sold by the pair for the 2 front shock absorbers.

For E39:
- 535 i and 540 i Saloon with M-Technic chassis only
- M5, all models

For all E34 versions, except M5
(not designed for versions with self-levelling)

Upper front shock absorber support ring for Porsche 911 type 997 Carrera 4, 4S, 4GTS and Turbo from 2005 to 2013 :

- 997 phase 1 3.6 Carrera 4 from 2005 to 2008
- 997 phase 1 3.8 Carrera 4S from 2005 to 2008

- 997 phase 2 3.6 Carrera 4 from 2009 to 2012
- 997 phase 2 3.8 Carrera 4S from 2009 to 2012

- 997 3.8 Carrera 4 GTS from 2012

- 997 3.6 Turbo from 2007 to 2009
- 997 3.8 Turbo from 2010 to 2013
- 997 3.8 Turbo S from 2010 to 2013

The ring is sold individually , and two quantities are required per vehicle.

Front suspension upper bearingright or left with ball bearing integrated branded FEBI for BMW 3 Series E30 Sedan, Coupé,Touring, and Cabriolet :

- All gasoline and diesel models including M3

WARNING: Not suitable for 4 wheel drive ix!

Center diameter for shock absorber rod: 14 mm

This cuplocated on the shock absorber of the front axle is valid for the right passenger side and the left driver side.

When noises are heard when passing over a bump, hole or cornering behavior deteriorates, these are signs that the upper bearings need to be changed.
We also recommend replacing them when new shocks are installed.

This product is sold individually.