Gearbox linkage

Sliding ring for fork of 5-speed 914.300.12 gearboxes mounted on all Porsche 914-4 produced from 1973 :

- 914-4 1.7 - 80 hp (022-W) of 1973
- 914-4 1.7 - 80 hp (022-EA) of 1973
- 914-4 1.7 - 72 hp (022-EB) of 1973
- 914-4 1.8 - 85 hp (021-AN) from 1974 to 1976
- 914-4 1.8 - 76 hp (022-EC) from 1974 to 1976
- 914-4 2.0 - 95 hp (039-GA) from 1973 to 1974
- 914-4 2.0 - 100 hp (039-GB) from 1973 to 1976
- 914-4 2.0 - 88 hp (039-GC) from 1975 to 1976

Quantity required per vehicle : 1

These shift lever mounting rings for 2cv (02/1970-07/1990) - Nylon are original accurate.

Theseshift lever rings for 2CV are essential for mounting the shift lever.

This gearshift bellows on bulkhead for 2cv (07/1949-07/1966) is a quality reproduction.

This elastic gearshift seal for 2CV is faithful to the original. Rubber bellows; it guarantees the tightness of the gearshift passage hole between the engine compartment and the passenger compartment for all models before July 1966.

Compatible models:

- 2CV A type A: 07/1949 to 03/1961
- 2CV AZ type AZ: 10/1954 to 03/1963
- 2CV AZL type AZ: 12/1956 to 03/1963
- 2CV AZLP type AZ: 09/1957 to 03/1963
- 2CV 4x4 "SAHARA" type AZ4/4: 09/1959 to 09/1966
- 2CV AZA type AZ-A: 03/1963 to 07/1966
- 2CV AZAM type AZ-AM: 03/1963 to 07/1966

This gear shift ball for 2cv and derivatives - black is compatible with all gear shift levers for 2cv models or derivatives.

The ball is made up of two half-spheres and a chrome-plated cover.

These bulkhead-mounted gear lever bellows for 2cv and derivatives after 1966 ensure the seal of the lever passage in the engine bulkhead.

It is compatible with all models of 2cv and derivatives after July 1966.

Gearshift shaft sleeve located at the output of the linkage cover case for the Porsche 914 produced between 1970 and 1972 :

- 914-4 1.7 - 80 hp (022-W) from 1970 to 1972
- 914-4 1.7 - 80 hp (022-EA) of 1972
- 914-4 1.7 - 72 hp (022-EB) of 1972
- 914-6 2.0 - 110 hp (901.36/37/38/39) from 1970 to 1972

Quantity required per vehicle : 1

These 2 rings allow you to repair the shift rod coupling of the gearbox linkage for Porsche 914-4 produced from 1973 :

- 914-4 1.7 - 80 hp (022-W) of 1973
- 914-4 1.7 - 80 hp (022-EA) of 1973
- 914-4 1.7 - 72 hp (022-EB) of 1973
- 914-4 1.8 - 85 hp (021-AN) from 1974 to 1976
- 914-4 1.8 - 76 hp (022-EC) from 1974 to 1976
- 914-4 2.0 - 95 hp (039-GA) from 1973 to 1974
- 914-4 2.0 - 100 hp (039-GB) from 1973 to 1976
- 914-4 2.0 - 88 hp (039-GC) from 1975 to 1976

Quantity required per vehicle: 1 set of 2 rings

Gearshift intermediate shaft ring for Citroën DS.
This plastic ring, also known as a ball joint, is mounted on the intermediate gear selector shaft. It allows you to restore the correct operation of the gear selector of your Citroën DS by replacing a worn or damaged part.
Dimensions: 19.5x26mm

This cover protects the rear end of the transmission fork control linkage. It mounts on Porsche 914 from 1970 to 1972 :

- 914-4 1.7 - 80 hp (022-W) from 1970 to 1972
- 914-4 1.7 - 80 hp (022-EA) of 1972
- 914-4 1.7 - 72 hp (022-EB) of 1972
- 914-6 2.0 - 110 hp (901.36/37/38/39) from 1970 to 1972

Quantity required per vehicle : 1

This Shift rod coupling mounts on the Porsche 911 and 912 from 1965 to 1988.
Replacing the RS13651 rings may be sufficient to remove the operating clearance. But sometimes the wear is too pronounced and requires the replacement of this linkage rod.

-> Porsche 912 :
- 912 1.6 from 1965 to 1969
- 912 E 2.0 of 1976

-> Porsche 911 :
- 911 2.0 from 1965 to 1968
- 911 2.0 T / L / E / S from 1967 to 1969
- 911 2.2 T / E / S from 1970 to 1971
- 911 2.4 T / E / S from 1972 to 1973
- 911 2.7 Carrera RS from 1973
- 911 2.7 from 1974 to 1977
- 911 2.7 S from 1974 to 1977
- 911 Carrera 2.7 from 1974 to 1976
- 911 Carrera 3.0 from 1976 to 1977
- 911 3.0 SC from 1978 to 1983
- 911 Carrera 3.2 from 1984 to 1986

-> Porsche 930 :
- 911 3.0 Turbo from 1975 to 1977
- 911 3.3 Turbo from 1978 to 1988

2 rings / silentblocs for the shif rod coupling for Porsche 356 B and C.

-> Porsche 356 B T5 :
- 356 B 1600 - 60 hp (616/1) from 1960 to 1961
- 356 B 1600 S - 75 hp (616/2) from 1960 to 1961
- 356 B 1600 Super 90 - 90 hp (616/7) from 1960 to 1961

-> Porsche 356 B T6 :
- 356 B 1600 - 60 hp (616/1) from 1962 to 1963
- 356 B 1600 S - 75 hp (616/12) from 1962 to 1963
- 356 B 1600 Super 90 - 90 hp (616/7) from 1962 to 1963

-> Porsche 356 C :
- 356 C 1600 - 75 hp (616/15) from 1964 to 1965
- 356 SC 1600 - 95 hp (616/16) from 1964 to 1965

These bushings can eliminate the operating clearance present at the gearbox linkage.

Attention, these rings are in the format of the original part. Potentially, if you have a remanufacturing shif rod coupling on your Porsche. The rings may not be suitable to present an operating clearance after assembly

MEYLE Socket, shift lever Golf 1 - Jetta 1

Suitable for:
- Golf 1 saloon, cabriolet and Caddy
- Jetta 1
- Scirocco

Rubber bellows on gearbox linkage under chassis
2 required on manual gearbox, only 1 on automatic gearbox.

For Combi Split & Bay Window, all models 1950 ->07/1979.

Rear part of gearbox control linkage.

For VW Kombi Split
Years: 1962 ->
Chassis: from no. 835 088 ->

Gearshift lever mounting pin on rod,

Gearshift linkage carter for Porsche 914 produced until 1972 :

- 914-4 1.7 - 80 hp (022-W) from 1970 to 1972
- 914-4 1.7 - 80 hp (022-EA) of 1972
- 914-4 1.7 - 72 hp (022-EB) of 1972
- 914-6 2.0 - 110 hp (901.36/37/38/39) from 1970 to 1972

Quantity required per vehicle: 1

Central cross-piece on manual gearbox control linkage.

For Transporter T25/T3, 08/1982 ->07/1992:
Petrol, Diesel engines & Turbo-Diesel
since chassis no. 24-D-000 001->
All models including Syncro version (4 x 4).

Manual Trans Shift rod bushing for manual transmission for Porsche 911 and 912 from 1969 to 1988 :

-> Porsche 912 :
- 912 1.6 of 1969
- 912 E 2.0 of 1976

-> Porsche 911 :
- 911 2.0 T / L / E / S of 1969
- 911 2.2 T / E / S from 1970 to 1971
- 911 2.4 T / E / S from 1972 to 1973
- 911 2.7 Carrera RS from 1973
- 911 2.7 from 1974 to 1977
- 911 2.7 S from 1974 to 1977
- 911 Carrera 2.7 from 1974 to 1976
- 911 Carrera 3.0 from 1976 to 1977
- 911 3.0 SC from 1978 to 1983
- 911 Carrera 3.2 from 1984 to 1986

-> Porsche 930 :
- 911 3.0 Turbo from 1975 to 1977
- 911 3.3 Turbo from 1978 to 1988

Gearbox linkage inner bellows for Porsche 911 and 912 from 1965 to 1971 :

-> Porsche 912 :
- 912 1.6 from 1965 to 1969

-> Porsche 911 :
- 911 2.0 from 1965 to 1968
- 911 2.0 T / L / E / S from 1967 to 1969
- 911 2.2 T / E / S from 1970 to 1971