Wings

Left front fender to be painted
model with turn signal hole and right-hand fitting slot
Top quality, close to original

For VW Beetle 1302

Passenger-siderear rightfender lower corner for BMW 3 series E30 phase 1 up to 08/1987 :

- 4-door sedan (including 4-wheel drive)
- 2-door Coupé (including 4-wheel drive)
- Convertible 325i from 09/1985 to 08/1987

ATTENTION: Not suitable for Touring or M3!

This body panel is delivered in storage paint. It will need to be treated and prepared to prevent corrosion from reappearing. Before final painting, it is essential to carry out a blank assembly to check alignment with the bumper and adjustment on the body.

This is an "adaptable" quality part, as it does not come from the manufacturer.

Quality part, referred to as adaptable" as it is not provided by the vehicle manufacturer"

Complete right rear fender for VW Transporter T25 / T3 from 1979 to 1992.

Pour Golf 5 tous modèles
(Pas pour Golf 5 Plus)

Rear replacement plate for front left-hand wheel housing
on standard or long chassis.

Pour VW Transporter T4 from 09/1990 to 06/2003
All models.

Left rear wing to be painted
model with 25 mm mounting slot

For VW Beetle 1200

Right-hand front fender complete with welded
with external bumper support and fuel filler. Without joint profile (part no. VA11804).

For VW Beetle :
- 1200 since 08/1973-> chassis N° 114 2000 001->
- 1300, 1500 since 08/1967-> chassis N° 118 000 001->

Rear left-hand lateral panel sill repair panel.
(part between the door and rear wing).

For Beetle all versions.

Left front wing including outer edge of the front panel, for Mercedes W123 Saloon, S123 Estate and C123 Coupé

Rear left-hand lateral panel sill repair panel.
(part between the door and rear wing).

For Beetle all versions.

Arc d'aile intérieur arrière gauche pour Golf 1, en tôle

Complete front and rear fender mounting kit (bolts and washers) for VW Cox sedan and convertible from 1938 to 2003.

This front wing clamp on chassis for 2cv vans from 1961 onwards holds the wing on the chassis.

For 2cvs and Dyanes after 1975 with an 11 mm rectangular hole.
It will require adaptation for earlier models.

This front wing clamp on chassis for DYANEs and Acadianes holds the wing on the chassis.

Suitable for 2cvs and Dyanes after 1975 with a rectangular hole of 11 mm.
It will require adaptation for earlier models

This front wing clamp on chassis for 2cv holds the wing on the chassis.

For 2cvs and Dyanes after 1975 with an 11 mm rectangular hole.

This front wing clamp on chassis for 2cv vans from 1961 onwards holds the wing on the chassis.

Suitable for 2cvs and Dyanes after 1975 with a 11 mm rectangular hole.

It will require adaptation for earlier models.

Aile avant droite de reproduction en polyester.
Dimensions d'origine. Qualité supérieure.

Pour VW Kübel 181, tous modèles
Années : 08/1969 ->12/1979

Right rear wing to be painted
model with 25 mm mounting slot

For VW Beetle 1200

Right rear wing to be painted
model with 20 mm mounting slot

For VW Beetle :
- 1200, 08/1973 ->07/1974
chassis N° 114 2000 001 ->114 2999 999.
- 1303, 08/1972 ->07/1974
chassis N° 133 2000 001 ->134 2999 999.

Whatever the body components, origin and quality, a "blank assembly" is essential to check and correct any adjustments before painting.