Cardan dust

This left front cardan shaft bellows kit for Renault 5 (01/1972-12/1985) - box sideis true to original.
This set of gaskets and bellows for the left front driveshaft for Renault R5 is compatible with many Renault models produced from the 70's to the 2000's.
Sealing ring dimensions :Outside diameter: 47.3 mmInside diameter: 27.8 mmHeight: 28 mm
It consists of the following components:
- 1 AVG bellows diam 30/85mm- 1 stainless steel collar- 1 box sealing ring- 1 grease bag

CEVAMcardan shaft bellows for Peugeot 205 GTI and CTI 1,6L (12/1984-09/1998)
This cardan shaft boot for Peugeot 205 GTI in NBR (nitrile rubber) will provide you with a quality seal.
For models :
- 205 GTI 1.6 L - 103hp 180A (XU5J) from 12/1984 to 10/1987- 205 GTI 1.6 L - 103hp 180A, 180Z (XU5J) from 10/1987 to 12/1989- 205 GTI 1.6 L - 116hp B6D (XU5JA) from 10/1987 to 12/1989- 205 CTI 1.6 L - 180A, 180Z (XU5J) from 03/1986 to 10/1990
For Diesel models :
- 205 Camionnette 1.7 L - 60hp 161A (XUD7) from 03/1994 to 05/1997- 205 TD 1.8 L - 78hp A8B (XUD7TE) from 01/1990 to 09/1998- 205 1.9 L - 64hp DJZ (XUD9A) from 10/1987 to 09/1998

This pocket of grease , sufficient for one bellows, will extend the life of your Mehari's universal joints.
Remember to degrease your parts before applying the new grease.

Special full universal joint with nuts diameter 100mm. Left or right side. Sold individually.

For VW 181, universal joint model
Years: 03/1973 ->12/1979
Chassis: depuis N° 183 2346 525->

Boot without slit for rear-axle cross-tube for all Porsche 356 :

-> Porsche 356 pre-A :
- 356 1100 - 40 hp (369) from 1950 to 1954
- 356 1300 - 44 hp (506 and 506/2) from 1951 to 1955
- 356 1300 S - 60 hp (589 and 589/2) from 1954 to 1955
- 356 1500 Cabriolet - 60 cv (527) from 1952
- 356 1500 - 55 hp (546 and 546/2) from 1953 to 1955
- 356 1500 S - 70 hp (528 and 528/2) from 1953 to 1955

-> Porsche 356 A :
- 356 A 1300 - 44 hp (506/1) from 1956 to 1957
- 356 A 1300 S - 60 hp (589/2) from 1956 to 1957
- 356 A 1600 - 60 hp (616/1) from 1956 to 1959
- 356 A 1600 S - 75 hp (616/2) from 1956 to 1959

-> Porsche 356 B T5 :
- 356 B 1600 - 60 hp (616/1) from 1960 to 1961
- 356 B 1600 S - 75 hp (616/2) from 1960 to 1961
- 356 B 1600 Super 90 - 90 hp (616/7) from 1960 to 1961

-> Porsche 356 B T6 :
- 356 B 1600 - 60 hp (616/1) from 1962 to 1963
- 356 B 1600 S - 75 hp (616/12) from 1962 to 1963
- 356 B 1600 Super 90 - 90 hp (616/7) from 1962 to 1963

-> Porsche 356 C :
- 356 C 1600 - 75 hp (616/15) from 1964 to 1965
- 356 SC 1600 - 95 hp (616/16) from 1964 to 1965

Also suitable for Carrera versions

The system witout slot, is like the original and requires to disassemble the rear-axle cross-tube.

Think of the clamp for universal boot reference UO10441

Does not contains fasteners.

Quantity required per car : 2

Sold individually

Front external cardan shaft bellows left or right for VW Transporter T5 from 2010 to 2015 from chassis no. WV1ZZZ7HZA-200001 or no. WV1ZZZ7JZA-200001 :
- 2.0 Petrol 115hp (AXA)
- 2.0 TDi 84hp (CAAA)
- 2.0 TDi 102hp (CAAB)
- 2.0 TDi 114hp (CAAD)

Kit for 1 rear inner or outer side:
1 bellows + mounting hardware + grease
Diameter 108 mm. Superior quality.

For Transporter T25 Syncro (4 x 4) with 16-inch wheels
all engines 85 ->07/92.

For E36 Saloon:
- 323 i and 328 i with automatic gearbox
- 323 i and 328 i up to ->09/95 with manual gearbox
- 325 i from 12/90->
- 325 td / tds up to ->09/95

For E36 Compact:
- 323 ti

For E36 Coupé:
- 323 i and 328 i up to ->09/95
- 325 i

For E36 Cabriolet:
- 323 i and 328 i up to ->09/95
- 325 i

For E36 Touring (Estate):
- 320 i with manual gearbox
- 323 iwith automatic gearbox
- 325 tds up to ->09/95 manual gearbox
- 328 i up to ->09/95

Constant-velocity boot, for the right or left side,

For E90 LCI & E91 LCI:
- 316 i N45N (E90 manual transmission only)
- 316 i N43
- 318 i N43 & N46N (manual transmission only)
- 320 i N43 & N46N (manual transmission only)

For E92 LCI & E93 LCI:
- 316 i N43 (E92 only)
- 318 i N43
- 320 i N43 & N46N (manual transmission only)

This collar for large cardan shaft bellows is suitable for the cardan shaft bellows on the wheel and gearbox sides of your Citroën 2Cv van.
2 are required for a complete universal joint.1 for the wheel-side bellows1 for gearbox-side bellows

These split sleeves make installation easy, as they do not require the trumpets to be removed.These trumpet bellows are supplied with screws and 2 clamps per side.Sold individually, in reinforced Heavy Duty quality.
For Brazilian VW Combi Split from 1957 to 1975 with trumpet rear axle.
Not suitable for models with universal joints.

For VOLKSWAGEN Transporter T5 with 6-speed manual gearbox (incl. 4 Motion) until 16.06.2013 :
- 2.5 TDi 130hp (AXD)
- 2.5 TDi 131hp (BNZ)
- 2.5 TDi 163hp (BLJ)
- 2.5 TDi 174hp (AXE, BPC)
- 3.2 R32 231hp (BDL)
- 3.2 R32 235hp (CFLA, BKK)
- 2.0 TDi 136hp(CAAE, CCHB)
- 2.0 TDi 140hp (CAAC, CCHA)
- 2.0 TDi 180hp (CFCA)

For BMW E39 520d, 523i, 525i/td/tds, 528i, 530i, M47, M52. M51 and M54 engines
535i automatic gearbox, M62 engine

Inner CV shaft boot, left or right-hand side,

For Ibiza (6K0):
- 1.0 50hp (AER)
- 1.1 45hp (AAU)
- 1.3 54hp (2G, AAV)
- 1.4 54hp (ANX)
- 1.4 60hp (ABD, AEX, AKV, APQ)
- 1.4 101hp (AFH)
- 1.6 75hp (ABU, AEE, ALM)

For Ibiza (6K1):
- 1.0 50hp (ALD, ANV, AUC)
- 1.0 69hp (AST, AVZ)
- 1.4 60hp (AKK, ANW, AUD)
- 1.4 75hp (APE, AUA)
- 1.4 101hp (AQQ, AUB)
- 1.6 75hp (ALM)

For Polo 86 from 75 ->81:
- LH or RH side all models

For Polo 86C,
RH side from chassis ..-E-050 307->:
- 1.05 40hp, 45hp and 50hp (ACM, AAK, AAU, GL, HZ)
- 1.1 50hp (HB)
- 1.3 54hp and 55hp (AAV, HK, 2G, MH, NZ)
- 1.3 58hp and 60hp (HJ, HH)
- 1.3 75hp (3F, GK)
- 1.3 G40 115hp (PY)

For Polo 86C,
LH side up to chassis ->..-H-168 730:
- 1.05 40hp, 45hp and 50hp (AAK, GL, HZ)
- 1.1 50hp (HB)
- 1.3 54hp and 55hp (HK, 2G, MH, NZ)
- 1.3 58hp and 60hp (HJ, HH)
- 1.3 75hp(3F, GK)
- 1.3 G40 115hp (PY)

External CV boot kit for Mercedes

For Mercedes W123, C123 and S123 all models

Mounts on the wheel side, on the right or left driveshaft

Kit for one side including boot, O-rings, clamps and grease

Boot diameter: 25/63mm
Length 98.5mm
Made of rubber

This homokinetic cardan shaft bellow for 2cv Van until 1968 is a quality reproduction.
This bellows for homokinetic cardan shafts is used on the wheel side as well as on the gearbox side. 
It is held in place by 2 specific rubber collars

For A4 (B5),
with manual gearbox: ATX
- 1.8 Turbo 180 hp (AJL)
- 2.4 136 hp (ASM)
- 2.4 156 hp (APC)
- 2.4 163 hp (AMM, AJG, APZ)
- 2.4 165 hp (AGA, ALF, AML, APS, ARJ)
- 2.5 TDi 150 hp (AFB, AKN)
- 2.6 139 hp and 150 hp (ACZ, ABC)
- 2.8 174 hp (AAH)
- 2.8 190 hp (ATX)
-2.8 193 hp (ACK, ALG, APR, AMX, AQD)

For A6 (C5),
with manual gearbox:
- 1.8 Turbo 150 hp and 180 hp (AJL, AWT)
- 1.9 TDi 110 hp and 115 hp (AFN, AVG, AJM)
- 1.9 TDi 130 hp (AVF, AWX)
- 2.4 136 hp and 156 hp (ASM, ALW, APC)
- 2.4 163 hp (AMM, AJG, APZ)
- 2.4 165 hp (AGA, ALF, AML, APS, ARJ)
- 2.4 170 hp (BDV)
- 2.5 TDi 150 hp and 155 hp (AFB, AKN, AYM)
- 2.5 TDi 163 hp (BCZ, BDG, BFC)
- 2.5 TDi 180 hp (AKE, BAU, BDH)
- 2.7 Turbo 230 hp (AJK)
- 2.8 180 hp (AGE)
- 2.8190 hp (ATX, BBJ)
- 2.8 193 hp (AGE, ACK, ALG, AMX, APR, AQD)
- 3.0 220 hp (ASN)

This collar for cardan shaft bellows, small model, is suitable for all cardan shaft bellows on your Citroën 2Cv fourgonnette.
4 are required for a complete universal joint.1 for the wheel-side bellows1 for the cardan shaft bellows on the gearbox side2 for the intermediate bellows

MEYLE Front dust bellows for front axle drive side for Porsche 911 type 997, 4 wheel drive :

- 997 phase 1 3.6 - 325 hp (M96.05) Carrera 4 from 2005 to 2008
- 997 phase 1 3.8 - 355 hp (M97.01) Carrera 4S from 2005 to 2008
- 997 phase 1 3.8 X51 - 380 hp (M97.01S) Carrera 4S from 2007 to 2008
- 997 phase 2 3.6 - 345 hp (MA 102) Carrera 4 from 2009 to 2012
- 997 phase 2 3.8 - 385 hp (MA 101) Carrera 4S from 2009 to 2012
- 997 phase 2 3.8 X51 - 408 hp (MA 101) Carrera 4S from 2009 to 2012
- 997 3.8 - 408 hp (MA 101) Carrera 4 GTS of 2012
- 997 3.6 Turbo - 480 hp (M97.70) from 2006 to 2009
- 997 3.8 Turbo - 500 hp (MA 170) from 2010 to 2013
- 997 3.8 Turbo S - 530 hp (MA 170) from 2010 to 2013

Quantity required per car : 2

Sold individually