Screws - Fixations

Eccentric screw for:
- 911 from 1965 to 1989
- 912
- 930

Total length: 28 mm
Head diameter: 22 mm
Threading diameter: 12 mm

Self-locking nut for front upper linkage bolt on Mazda MX-5 NA, NB and NBFL

For all NA, NB and NBFL models with or without sport chassis

Allows the upper front linkage to be secured with the MX15496 screw

One required per linkage
Sold individually

Genuine Mazda part

O-ring for bearing housings on trumpet rear swing arm

Original VW Classic Parts

For VW Cox (-07/1967)

Eccentric washer for rear lower arm adjustment screw for Mazda RX8

For RX-8 all models from 2003 to 2012

Washer that goes with screw part no.RX02780 for securing the rear lower arm of the rear axle


Original MAZDA part

Rear axle eccentric bolt for:
- 911 from 1965 to 1973
- 912

Length of the threaded section : 14 mm
Total length: 36mm
Head diameter: 24 mm
Length of the middle section : 4 mm
Diameter of the middle section : 18 mm

Rear lower linkage screw for Mazda RX-8

For RX-8 all models from 2003 to 2012

enables you to fix the rear of the front lower linkage
One screw required per linkage

Sold individually
Original MAZDA part

Front lower arm to rear hub clamp nut for Mazda RX8

For RX-8 all models from 2003 to 2012

enables you to tighten the front lower arm on the rear hub carrier with the RX02796 screw (see diagram)

One nut required per side
Sold individually

Genuine Mazda part

Eccentric screw for front lower arm adjustment on cradle for Mazda RX-8

For RX-8 all models from 2003 to 2012

enables you to attach the lower arm located at the front of the rear axle

1 screw required per side
Original MAZDA part

Lower front linkage adjustment screw for MX5 NC NCFL

- Suitable for both right and left
- You need a screw on each side of the car
- Original MAZDA part
Fits all Mazda MX5 NC NCFL models

Key for suspension ball joint for Citroën Traction 11hp.
This key locks the axial movement of the pivot.
Dimension: 2.5x3x12mm
Sold individually.

Washer onmounting screw for slanted arms on axle with universaljoints.
2 required per car, 4 per car, left or right-hand, sold per unit.
For:
- Beetle 1302, 1303 & Automatic from 08/1967->
- Karmann-Ghia
- Type 3
-181, Buggy, 356 Réplica
with Type 1 gearbox with universal joints

Rear axle eccentric screw for :
- 911 type G from 1974 to 1989- 924 2.0 and 2.5 from 1976 to 1988- 944 from 1982 to 1991- 968 from 1992 to 1995
Length of threaded section: 17 mmTotal length: 34 mmAttaches with 36 mm opening key

Front axle mounting washer for VW Combi Split up to 07/1967.

Pin nut drum / rear hub for Porsche 924 :

- 924 2.0 - 125 hp from 1976 to 1985
- 924 Turbo - 170 hp from 1979 to 1980
- 924 Turbo - 177 hp from 1981 to 1984
- 924 Carrera GT 1981

Pin nut drum / rear hub for Porsche 944 phase 1 :

- 944 2.5 - 163 hp from 1982 to 1985

Rear anti-roll bar bushing for:
- 911 from 1965 to 1977
- 912
- 914

Set of 8 shims for plating the front axle to the body.
Treated steel.
For Combi Split and Combi Bay Window

Rear stabilizer bar bracket for Porsche 911 type F and 912 from 1965 to 1971 :

- Porsche 911 type F :

- 911 2.0 from 1965 to 1967
- 911 2.0 T / L / E / S from 1967 to 1969
- 911 2.2 T / E / S from 1970 to 1971

- Porsche 912 :

- 912 1.6 - 90 hp (616.36) from 1966 to 1968

The bracket is sold individually, and two quantities are required per vehicle.

Kit of 4 sealing rings on the upper and lower tubes of the front axle body.

For VW Combi Split T1
Years: 1950 ->07/1967

Clamping nut for M10 screws.
Suitable for pivot pins on upper and lower suspension arms for VW Beetle from 1947 to 07/1965 and up to chassis No. 115 999 000 as well as for Karmann-Ghia T14 from 08/1955 to 07/1965 up to chassis No. 145 999 000.
Also suitable for :M10 x 82 lower engine-mounting screw for Cox and CombiEngine mounting screw for Combi and Transporter in M10 x 97Motor mounting screw with starter for Cox, Combi in M10 x 110