Inlet manifold

Central part of the pipe for 34 PICT carburettor

For VW Cox, Karmann-Ghia, Combi, 181...
with 1600 dual intake engine and single heater

Adaptable to Combi with servo-brake by drilling the pipe for the vacuum hose.

Original "single intake " manifold for VOLKSWAGEN Combi Split Brazil (1957-1975)

Original "single intake " manifold for VW Cox and Combi 1200 engines

Center pipe for 30/31 PICT carburetor
For 1300 AB engines with dual intake and single heater.
We strongly recommend that you also take a carburettor riser part no. "VC70520", as the carburettor can sometimes touch the dynamo or alternator.

Fixing clamps for a rubber sleeve on intake manifolds.
Kit of 1 small 1 large for left or right side of intake manifold.

For VW :
- Cox, Karmann, Combi, 181
with Type 1 double intake engine, 1300

Aluminum intake pipes with special curve for Porsche turbine clearance if required.

For 2 Weber IDF, Dellorto DRLA or Empi HPMX 36 / 40 / 44 mm carburetors on Type 4 engines.

Original single-intake pipe with preheating, without engine speed limiter.
For type 1 engines: 1500cc (42hp), Industrial 126/A.
Original Volkswagen Classic Parts.

For VW Kombi Split 1500 42hp

Tilted CB Performance (USA ) aluminum pipes catch cylinder offset to align twin carburetors.

For 2 Weber IDF, Dellorto DRLA or Empi HPMX carburetors
For Type 1 engines with dual intake.

Center pipe for 30/31 PICT carburetor

For 1300 AR engines with dual intake and dual heater.

This manifold is equipped with double reheating, with a smaller internal diameter than the single reheating model. The VC40302 side pipes cannot be mounted on it (large diameter).

WEBER 46 IDA3C intake pipes for Porsche 911 and 914-6.
Manufactured in the UK to the highest standards, these intake pipes are slightly higher than the original (90mm) and have been reinforced to guarantee excellent longevity.
Engine-side diameter: 40mmCarburetor-side diameter: 46mm

Intake manifold with aluminum gaskets to fit 2 Weber 45 DCOE carburetors for Triumph TR4.
- Kit of parts including cast aluminum intake manifolds and linkage kit to fit 2 Weber 45 DCOE carburetors on Triumph TR4.

Rubber bellows for connection and sealing between center pipe and side intake manifolds on Type 1 1300 and 1600cc engines.Sold individually.
For :- VW Cox, Karmann-Ghia, Combi engines: 1300 and 1600cc double intake.

OE or OE type electric heated intake manifold for VW Cox
Production by BBT
- All Type 1 engines
Can be adapted to other intake pipes if diameter and length allow.
Simple connection:
The fuse wire with the flat lug is connected to the coil, and the wire with the round lug is connected to a stud or a screw on the motor plate for ground.

- Works on 6 or 12 volts.

Weber 45 DCOE intake manifold for BMW

This kit allows for the mounting of 2 Weber 45 DCOE carburetors on BMWs equipped with the M10 engine:
1600
1602
1802
316 E21
316 E30

Intake pipe in one piece
Flex flange and mounting kit provided.

CSP short intake pipes in aluminium for Porsche 914-4 :

- 914-4 1.7 - 80 hp (022-W) from 1970 to 1973
- 914-4 1.7 - 80 hp (022-EA) from 1972 to 1973
- 914-4 1.7 - 72 hp (022-EB) from 1972 to 1973
- 914-4 1.8 - 85 hp (021-AN) from 1974 to 1976
- 914-4 1.8 - 76 hp (022-EC) from 1974 to 1976
- 914-4 2.0 - 95 hp (039-GA) from 1973 to 1974
- 914-4 2.0 - 100 hp (039-GB) from 1973 to 1976
- 914-4 2.0 - 88 hp (039-GC) from 1975 to 1976

For two 40 mm Weber IDF or Dellorto DRLA carburettors, they offer an optimized maximum flow with a diameter adjusted to 40 mm. Lots of material available on the staves to allow them to be reworked as needed.

Supplied with German quality studs, screws and gaskets.

Weber 40 DCOE intake manifold for BMW

This kit allows for the mounting of 2 Weber 40 DCOE carburetors on BMWs equipped with the M10 engine:
1600
1602
1802
316 E21
316 E30

Intake pipe in one piece
Flex flange and mounting kit provided.

CB Performance intake pipes for mounting 2 Weber IDF or Dellorto DRLA 36 / 40 / 44 mm carburetors on Type 1 double intake cylinder heads.

Features:
Straight pipes, to promote intake flow (offset carburetors)
Special casting with lots of material on the cylinder head side,
to enlarge and polish ducts.

WEBER 40 IDA3C intake pipes for Porsche 911 and 914-6.

Manufactured in the UK to the highest standards, these intake pipes are slightly higher than the original (90mm) and have been reinforced to guarantee excellent longevity.

Engine-side diameter: 36mm
Carburetor-side diameter: 40mm

Top quality aluminium central intake pipe!
EMPI.
For 1 Weber IDF, Dellorto DRLA or Empi HPMX 36/40/44 mm carburettor on Type 1 dual-intake engine.

Intake manifold SU HS6 for Volvo

For Volvo equipped with engine type B18 or B20: :
- Series 140 (142, 144, 145)
- Amazon P120, P130, P220
- Volvo P1800
- Volvo PV544
- Volvo Duett

This aluminum intake manifold accommodates two SU HS6 carburetors.