Rigid brake hose

Rigid copper brake hose 45 cm for 4.75 mm diameter
- Male / Male fittings- Fitting type: 3/8" 24UNF- Thread length: 18 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using a 10mm wrench.

This left rear brake hose for 2CV Van (01/1972-03/1978)is to be formed.

This rigid brake hose for 2CV in 3.5mm diameter copper is to be formed.
It connects the rear tee to the left rear wheel cylinder with a 8 wrench.
This hose is compatible with all front drum as well as disc brake models from June 1970.

Beware! Use the proper barrel seals for DOT4 and DOT5 or LHM brake fluid. LHM (green) fluid is very corrosive to parts not intended for its use, using the wrong seals or brake fluid could severely damage your brake system.

This brake hose kit for Peugeot 504 (09/1974-09/1981) - M10x1 respects original dimensions.
This set of rigid brake hoses for Peugeot 504 is made of copper.The high quality copper hoses are the length of the original assembly and will require forming before fitting.
All circuit connections via M10x1 end fittings.This set includes:- 2 front pipes, left and right- 2 right and left rear pipes- 2 right and left front intermediate hoses
Caution: if your vehicle has been modified, check the diameter of the wheel cylinder and the wrench required to tighten the brake hose connectors.Use only DOT 4 or DOT 5 brake fluid.

Rigid copper brake hose 51cm for 3.5 mm diameter
- Male / Male ferrules- End fitting type: M8 x 125- Thread length: 20 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using an 8mm wrench.

This rigid brake hose kit for Citroën traction 11 BN after 07/1952 includes all the rigid tubes needed to replace all those fitted to your traction vehicle.
Over time, original brake tubes oxidize, crack or become blocked, compromising the safety of your braking system. Irregular braking or leaks can be signs that the system needs replacing.
This rigid hose kit is essential to restore your Traction to a state-of-the-art condition and drive with peace of mind.
Compatible models:- Traction Avant 11B Berline 4 portes 11 "Performance", type 11B de 07/1952 à 01/1955, Moteur, type 11cv perfo 1911cc (56cv)- Traction Avant 11C Commercial 11 "Performance", type 11B from 03/1954 to 1957, Engine, type 11hp D 1911cc (59hp)- Traction Avant 11B Berline 4 portes 11 "Performance", type 11B de 02/1955 à 07/1957, Moteur, type 11cv D 1911cc (59cv)

Rigid front brake hose on master cylinder for Porsche 911 type F, G and 912 from 1968 to 1977:
- Porsche 911 type F :
- 911 2.0 T / L / S from 1968- 911 2.0 T / E / S from 1969- 911 2.2 T / E / S from 1970 to 1971- 911 2.4 T / E / S from 1972 to 1973- 911 2.7 Carrera RS from 1973
- Porsche 911 type G without brake servo :
- 911 2.7 from 1974 to 1977- 911 S 2.7 from 1974 to 1977- 911 Carrera 2.7 from 1974 to 1976- 911 Carrera 3.0 from 1976 to 1977- 911 Turbo 3.0 from 1975 to 1977
- Porsche 912 :
- 912 1.6 from 1966 to 1969- 912 2.0 from 1976
Only suitable for vehicles with left-hand drive.

Internal rear brake hose for Porsche 356 B T6 2000 from 1962 to 1963 :
- 356 B T6 2000 Carrera GS (587/1) - 130hp from 1962 to 1963- 356 B T6 2000 Carrera GT (587/2) - 160hp from 1963
The hose is sold individually and is suitable for either the left or right side.

This intermediate brake hose for DYANE -STAINLESS STEEL- 3.5mm for 8mm spanners is higher quality than the original.

This pipe from the master cylinder to the rear is made of stainless steel. It is compatible with all models with disc brake systems except Acadianes.
Its high quality manufacturing makes it highly reliable with durability superior to the majority of the other elements in the car.
You connect it to the master cylinder and wheel cylinder with an 8mm spanner.

Watch out!!! Your vehicle may have been modified, so check the diameter of the wheel cylinder and the spanner you need to tighten the brake hose ends.
Use only LHM brake fluid.
LHM fluid is very corrosive to parts not designed for its use, and the wrong brake fluid could seriously damage your braking system.

110 cm rigid copper brake hose for 3.5 mm diameter
- End fittings Male / Male- End fitting type: M8 x 125- Thread length: 20 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using an 8mm wrench.

This brake hose kit for RENAULT 9 (09/1980-09/1987) respects the original dimensions.
This set of rigid brake hoses for RENAULT 9 is made of copper.The high quality copper hoses are the length of the original assembly and will require forming before fitting.
All circuit connections via M10x1 end fittings.This set includes:- 2 front pipes, left and right- 2 right and left rear pipes- central hose
Caution: if your vehicle has been modified, check the diameter of the wheel cylinder and the wrench required to tighten the brake hose nipples.Use only DOT 4 or DOT 5 brake fluid.

Rigid copper brake hose 319 cm for 3.5 mm diameter
- End fittings Male / Male- End fitting type: M8 x 125- Thread length: 20 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using an 8mm wrench.

This Intermediate rear brake hose for 2cv (06/1964-06/1970) - 4.5mm is a higher quality than the original.

This intermediate brake hose for 2CV in 4.5mm is compatible with assemblies requiring a 10 wrench.It was replaced from June 1970 by a complete system in 3.5mm and 8 wrench.Caution!!! your vehicle may have been modified, check the diameter of the wheel cylinder and the wrench needed to tighten the brake hose ends.


Use only DOT4 or DOT5 brake fluid.
LHM fluid is very corrosive to parts not intended for its use, the wrong brake fluid could severely damage your brake system.

Flexible d'alimentation sur bloc ABS depuis le réservoir de liquide de frein pour VOLKSWAGEN Transporter T4 de 1999 à 2003.
Longueur 130mm.

Kit canalisations rigides de freins pour VW Combi Split Brésilien de 1957 à 1975.

Rigid copper brake hose 111 cm for 3.5 mm diameter
- End fittings Male / Male- End fitting type: M8 x 125- Thread length: 20 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using an 8mm wrench.

Rigid copper brake hose 280 cm for 4.75 mm diameter
- End fittings Male / Male- End fitting type: M12 x 100- Thread length: 20 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using a 12mm wrench.

Right rear rigid brake line for Volkswagen Scirocco 3
For VW Scirocco 3 :- All petrol and TDI models from 2009 to 2017
Technical specifications:- Thread size 1: M10x1- Thread size 2: M12x1
This rigid brake hose is attached to the right rear caliper on the passenger side and connects to the brake hose.

This rear transverse brake hose for Dyane (08/1967-06/1970) - 4.5mm is of superior quality to the original.
This 4.5mm transverse brake hose for Dyane is compatible with assemblies requiring a 9 key and has been used on the following Dyane models:- DYANE - AYA - (08/1967-01/1969)- DYANE 4 - AYA2 - (03/1968-02/1970)- D6 - AYA3 - (01/1968-04/1968)- DYANE 6 - AYA3 - (06/1968- 02/1970)
It was replaced in June 1970 by a complete system in 3.5mm and key of 8. Caution! your vehicle may have been modified, check the diameter of the wheel cylinder and the key needed to tighten the brake hose ends.
The fitting is a 9 thread with a 10 wrench opening.

Use only DOT4 or DOT5 brake fluid.LHM fluid is highly corrosive to parts not intended for its use, and the wrong brake fluid can seriously damage your braking system.

Kit of rigid copper brake hoses for:
- 356 B from 1960 to 1963

This intermediate brake hose for Meharis - STAINLESS STEEL - 3.5mm for 8mm spanners is higher quality than the original.

This pipe from the master cylinder to the rear is made of stainless steel. It is compatible with all models with disc brake systems.
Its high quality manufacturing makes it highly reliable with durability superior to the majority of the other elements in the car.
You connect it to the master cylinder and wheel cylinder with an 8mm spanner.

Watch out!!! Your vehicle may have been modified, so check the diameter of the wheel cylinder and the spanner you need to tighten the brake hose ends.
Use only LHM brake fluid.
LHM fluid is very corrosive to parts not designed for its use, and the wrong brake fluid could seriously damage your braking system.