Rigid brake hose

This brake hose from the master cylinder to the front for Meharis -STAINLESS STEEL-3.5mm-with 8mm spanner fitting is superior quality.

This rigid hose connects the master cylinder to the brake callipers and is compatible with all disc brake models.
Its 3.5mm diameter stainless steel tube is higher quality than the original.

This rear transverse brake hose for 2cv (06/1964-06/1970) - 4.5mm is of superior quality to the original.
This 4.5mm transverse brake hose for 2CV is compatible with assemblies requiring a size 9 wrench. It was replaced in June 1970 by a complete system in 3.5mm and size 8 wrench. Caution: your vehicle may have been modified, so check the diameter of the wheel cylinder and the wrench required to tighten the brake hose ends.
The fitting is a 9 thread with a 10 wrench opening.

Use only DOT4 or DOT5 brake fluid.LHM fluid is highly corrosive to parts not intended for its use, and the wrong brake fluid can seriously damage your braking system.

This rear transverse brake hose for AMI6 and AMI8 (04/1961-09/1969) - 4.5mm is of superior quality to the original.
This 4.5mm transverse brake hose for AMI6 and AMI8 is compatible with assemblies requiring a size 9 wrench. It was replaced in September 1969 by a complete system in 3.5mm and size 8 wrench. Please note that your vehicle may have been modified, so check the diameter of the wheel cylinder and the wrench required to tighten the brake hose ends.
The fitting is a 9 thread with a 10 wrench opening.

Use only DOT4 or DOT5 brake fluid.LHM fluid is highly corrosive to parts not intended for its use, and the wrong brake fluid can seriously damage your braking system.

This front brake hose for 2cv Fourgonnette (10/1967-09/1972) - 4.5mm is a higher quality than the original.

This front brake hose for 2CV Van in 4.5mm is compatible with assemblies requiring a 9 wrench.
It was used on the following 2CV Fourgonnette models:
- 2CV AK350 (10/1967-02/1970)
- 2CV AZU-A (03/1968-09/1972)It succeeded the intermediate mounting using banjos for the front brakes, and was replaced from June 1970 by a complete system in 3.5mm and 8 wrench.

Caution!!! your vehicle may have been modified, check the wheel cylinder diameter and the wrench needed to tighten the brake hose ends.


Use only DOT4 or DOT5 brake fluid.
LHM fluid is very corrosive to parts not intended for its use, the wrong brake fluid could severely damage your brake system.

This front brake hose on box for 2cv Van (10/1967-09/1972) - 4.5mm is a higher quality than the original.

This front brake hose on box for 2CV Van in 4.5mm is compatible with assemblies requiring a 9 wrench.
It was used on the following 2CV Fourgonnette models:
- 2CV AK350 (10/1967-02/1970)
- 2CV AZU-A (03/1968-09/1972)It succeeded the intermediate mounting using banjos for the front brakes, and was replaced from June 1970 by a complete system in 3.5mm and 8 wrench.

Caution!!! your vehicle may have been modified, check the wheel cylinder diameter and the wrench needed to tighten the brake hose ends.


Use only DOT4 or DOT5 brake fluid.
LHM fluid is very corrosive to parts not intended for its use, the wrong brake fluid could severely damage your brake system.

This intermediate rear brake hose for 2CV Van AZU-A (03/1963-01/1972) - 4.5mm is a higher quality than the original.

This intermediate brake hose for 2CV in 4.5mm is compatible with assemblies requiring a 10 wrench.It was replaced from June 1970 by a complete system in 3.5mm and 8 wrench.Caution!!! your vehicle may have been modified, check the diameter of the wheel cylinder and the wrench needed to tighten the brake hose ends.


Use only DOT4 or DOT5 brake fluid.
LHM fluid is very corrosive to parts not intended for its use, the wrong brake fluid could severely damage your brake system.

This rigid brake hose kit for Citroën traction 11 BN after 07/1952 includes all the rigid tubes needed to replace all those fitted to your traction vehicle.
Over time, original brake tubes oxidize, crack or become blocked, compromising the safety of your braking system. Irregular braking or leaks can be signs that the system needs replacing.
This rigid hose kit is essential to restore your Traction to a state-of-the-art condition and drive with peace of mind.
Compatible models:- Traction Avant 11B Berline 4 portes 11 "Performance", type 11B de 07/1952 à 01/1955, Moteur, type 11cv perfo 1911cc (56cv)- Traction Avant 11C Commercial 11 "Performance", type 11B from 03/1954 to 1957, Engine, type 11hp D 1911cc (59hp)- Traction Avant 11B Berline 4 portes 11 "Performance", type 11B de 02/1955 à 07/1957, Moteur, type 11cv D 1911cc (59cv)

Rigid copper brake hose 30 cm for 4.75 mm diameter
- End fittings Male / Male- End fitting type: M12 x 100- Thread length: 20 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using a 12mm wrench.

Rigid copper brake hose 140 cm for 4.75 mm diameter
- Male / Male fittings- Nipple type: 3/8" 24UNF- Thread length: 21 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using an 11mm wrench.

Rigid brake hose kit for Porsche 911 type F and 912 from 1965 to 1967 :
- 911 from 1965 to 1967- 912 from 1966 to 1967
Only suitable for vehicles with single-circuit braking. At the end of '67, Porsche switched to dual-circuit braking. Kit contains 9 hoses.

This left front brake hose for Dyane (06/1970-07/1977) - drums is true to the original.

This rigid hose for Dyane made of 3.5mm diameter copper is to be formed.
It connects the Tee on top of the box to the left front wheel cylinder with a 8 wrench.
This hose is compatible with all front drum brake models from June 1970 on.

This rear transverse brake hose for 2cv Fourgonnette AZU-A (03/1963-01/1972) - 4.5mm is of superior quality to the original.
This 4.5mm transverse brake hose for 2CV Fourgonnette AZU is compatible with assemblies requiring a wrench size 9. It was replaced in June 1970 by a complete system in 3.5mm and wrench size 8. Caution: your vehicle may have been modified, so check the diameter of the wheel cylinder and the wrench required to tighten the brake hose ends.
The fitting is a 9 thread with a 10 wrench opening.

Use only DOT4 or DOT5 brake fluid.LHM fluid is highly corrosive to parts not intended for its use, and the wrong brake fluid can seriously damage your braking system.

230 cm rigid copper brake hose with 4.75 mm diameter
- Spigots Male / Male- Nipple type: 3/8" 24UNF- Thread length: 18 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using a 10mm wrench.

Complete set of rigid PVF steel brake hoses.
Complete lines for models without ABS, brake servo or pressure regulator.

For Volkswagen Golf 1 from 04/1974 to 07/1979

This custom-made brake line kit will enable you to restore the braking system of your Golf 1.

Complete set of rigid PVF steel brake hoses.
Complete lines for models without ABS, with brake servo and pressure regulator.

For Volkswagen Golf 1 from 04/1974 to 07/1979

This custom-made brake line kit will enable you to restore the braking system of your Golf 1.

Complete set of rigid PVF steel brake hoses.
Complete lines for models without ABS, with brake servo and without pressure regulator.

For Volkswagen Golf 1 from 04/1974 to 07/1979

This custom-made brake line kit will enable you to restore the braking system of your Golf 1.

Complete set of rigid PVF steel brake hoses.
Complete lines for models without ABS, with brake servo and pressure regulator.

For Volkswagen Golf 1 from 08/1979 to 02/1984

This tailor-made brake line kit will enable you to restore the braking system of your Golf 1.

Complete set of rigid PVF steel brake hoses.
Complete lines for models with ABS.

For VW Golf 2 1.0-1.8 Petrol and Diesel from 08/1986 to 07/1988.

This made-to-measure brake line kit will enable you to restore the braking system of your VW Golf 2.

Complete set of rigid PVF steel brake hoses.
Complete lines for models with ABS and rear brake discs .

For VW Golf 2 1.0-1.8 Petrol and Diesel from 08/1989 to 07/1992.

This customized brake line kit will enable you to restore the braking system of your VW Golf 2.

Rigid front brake hose on master cylinder for Porsche 914 from 1970 to 1976 :
- 914-4 1.7 - 80 hp (022-W) from 1970 to 1973- 914-4 1.7 - 80 hp (022-EA) from 1972 to 1973- 914-4 1.7 - 72 hp (022-EB) from 1972 to 1973- 914-4 1.8 - 85 hp (021-AN) from 1974 to 1976- 914-4 1.8 - 76 hp (022-EC) from 1974 to 1976- 914-4 2.0 - 95 hp (039-GA) from 1973 to 1974- 914-4 2.0 - 100 hp (039-GB) from 1973 to 1976- 914-4 2.0 - 88 hp (039-GC) from 1975 to 1976- 914-6 2.0 - 110 hp (901.36/37/38/39) from 1970 to 1972