Rigid brake hose

This rear brake hose for 2cv (06/1964-06/1970) - 4.5mm is a higher quality than the original.

This rear brake hose for 2CV in 4.5mm is compatible with mounts that require a 9 wrench and mounts on the end of the rear hose. It was only used on the 2CV sedan on the Hybrid banjo front mounting and a few months at the launch of the 2CV4 and 2CV6. It was replaced in June 1970 by a complete system in 3.5mm and key of 8.

Caution!!! your vehicle may have been modified, check the diameter of the wheel cylinder and the key needed to tighten the brake hose ends.


Use only a DOT4 or DOT5 brake fluid.
The LHM fluid is very corrosive to parts that are not intended for its use, a bad brake fluid could severely damage your braking system.

This brake hose kit for Peugeot 504 (09/1974-09/1981) - M10x1 respects original dimensions.
This set of rigid brake hoses for Peugeot 504 is made of copper.The high quality copper hoses are the length of the original assembly and will require forming before fitting.
All circuit connections via M10x1 end fittings.This set includes:- 2 front pipes, left and right- 2 right and left rear pipes- 2 right and left front intermediate hoses
Caution: if your vehicle has been modified, check the diameter of the wheel cylinder and the wrench required to tighten the brake hose connectors.Use only DOT 4 or DOT 5 brake fluid.

This rear brake hose kit for 2cvs - STAINLESS STEEL is higher quality than the original.

This pair of rear spiral brake hoses is made of stainless steel. It is compatible with all models from June 1981.
Its high quality manufacturing and the preforming of the different hoses make them highly reliable with durability superior to the majority of the other elements in the car.
Use an 8mm spanner to fit the connector ends to the central fitting and wheel cylinders.

Watch out!!! Your vehicle may have been modified, so check the diameter of the wheel cylinder and the spanner you need to tighten the brake hose ends.

Watch out!!! Check the colour of your brake fluid and barrel gaskets, use the right gaskets for your brake fluid:
- with red dots for DOT4 or DOT5 liquid.
- green dot for the LHM

LHM fluid is very corrosive to parts not intended for its use, and the wrong brake fluid could seriously damage your braking system.

This rear and intermediate brake hose kit for 2cvs - STAINLESS STEEL is higher quality than the original.

This set of rigid brake hoses is made of stainless steel. It is compatible with all models with a front disc brake system.
Its high quality manufacturing and the preforming of the different rear hoses make them highly reliable with durability superior to the majority of the other elements in the car.
All connection ends to the master cylinder and wheel cylinder can be fitted with an 8 mm spanner.

This package includes:
- the 2 spiral hoses connecting the rear drums
- the intermediate pipe from the master cylinder to the rear

Watch out!!! Your vehicle may have been modified, so check the diameter of the wheel cylinder and the spanner you need to tighten the brake hose ends.
Use only LHM brake fluid.
LHM fluid is very corrosive to parts not intended for its use, and the wrong brake fluid could seriously damage your braking system.

This front left brake hose for 2cvs with front drum brakes is true to the original.

This rigid hose made of copper with a 3.5mm diameter needs shaping.
It connects the tee on top of the gearbox to the front left wheel cylinder with 8mm fitted nipples.
This hose is compatible with all front drum brake models from June 1970.

This brake hose between callipers for 2cvs with disc brakes is true to the original.

This rigid brake hose made of copper with a 3.5mm diameter needs shaping.
It connects the callipers over the gearbox with 8mm fitted connectors.
This hose is compatible with all models with front disc brakes.

This front brake hose from the master cylinder to the tee for 2cvs with front disc brakes is true to the original.

This copper rigid brake hose with 3.5mm diameter needs shaping.
It connects the tee on top of the box to the master cylinder.
This hose is compatible with all models with front disc brakes from June 1978.

This right rear brake hose for 2CV needs shaping

This rigid brake hose made of copper with a 3.5mm diameter needs shaping.
It connects the rear tee to the right rear wheel cylinder with 8mm keyed connectors.
This hose is compatible with all front drum and disc brake models from June 1970.

Rigid brake line kit for Porsche 356 BT5 from 1960 to 1961 :
- 356 BT5 from 1960 to 1961
The kit contains 8 rigid brake hoses and is suitable for single-circuit vehicles without brake booster.

Rigid brake line kit for 1968 Porsche 911 F type :
- 911 2.0 T / L / S from 1968
This kit of 9 rigid hoses is suitable for vehicles with a single brake circuit and no brake booster.

Rigid brake line kit for Porsche 356 BT6 from 1962 to 1963 :
- 356 BT6 from 1962 to 1963
The kit contains 8 rigid brake hoses and is suitable for single-circuit vehicles without brake booster.

Brake line kit for Porsche 911 type G from 1974 to 1976 :
- 911 2.7 from 1974 to 1976- 911 S 2.7 from 1974 to 1976- 911 Carrera 2.7 from 1974 to 1976- 911 Carrera 3.0 from 1976
This set of 10 rigid hoses is suitable for vehicles with dual brake circuits and no brake booster.

This brake hose kit for Citroën BX (09/1982-07/1989) - without ABS is of superior quality to the original.
This set of rigid brake hoses is made of copper. It is compatible with all models from launch to the introduction of ABS in July 1989.The high-grade copper hoses are the exact length of the original assembly and will require shaping before fitting.
All circuit connections to the master cylinder and wheel cylinders are made using a size 8 wrench.
This assembly includes- hoses from the front distributor to the right and left front calipers- the (long) hose connecting to the rear distributor- intermediate hose from master cylinder to front distributor- intermediate hose from master cylinder to rear distributor- rear drum hoses
Caution: if your vehicle has been modified, check the wheel cylinder diameter and the wrench required to tighten the brake hose ends.Use only LHM brake fluid.LHM fluid is highly corrosive to parts not intended for its use, and the wrong brake fluid can seriously damage your braking system.

This brake hose kit for 2cvs with front disc brakes - STAINLESS STEEL is higher quality than the original.

This set of rigid brake hoses is made of stainless steel. It is compatible with all models with front disc brake systems from June 1981. Its high quality manufacturing and the preforming of the different hoses make them highly reliable with durability superior to the majority of the other elements in the car.
All connection ends to the master cylinder and wheel cylinder can be fitted with an 8 mm spanner.

This package includes:
- the front disc connection hose
- the 2 spiral hoses connecting the rear drums
- the intermediate spiral pipe from the master cylinder to the front
- the intermediate pipe from the master cylinder to the rear

Watch out!!! Your vehicle may have been modified, so check the diameter of the wheel cylinder and the spanner you need to tighten the brake hose ends.
Use only LHM brake fluid.
LHM fluid is very corrosive to parts not intended for its use, and the wrong brake fluid could seriously damage your braking system.

This set of rigid brake hoses for RENAULT 20 is made of copper.The high quality copper hoses are the length of the original assembly and will require forming before fitting.
All circuit connections via M10x1 end fittings.This set includes:- 2 front pipes, left and right- 2 right and left rear pipes- 2 outer right and left rear pipes- one standard and one extended central hose
Caution: if your vehicle has been modified, check the diameter of the wheel cylinder and the wrench required to tighten the brake hose ends.Use only DOT 4 or DOT 5 brake fluid.

Rigid brake hose kit for Porsche 356 Pre-A and A from 1950 to 1959 :
- 356 Pre-A from 1950 to 1955- 356 A from 1956 to 1959
This kit of 7 brake hoses is suitable for vehicles with a single brake circuit.

Flexible de sortie de réservoir de frein pour VOLKSWAGEN Transporter T4 de 1999 à 2003 pour véhicule avec programme électronique de stabilité ESP et depuis châssis n°70-Y-027264
Longueur : 80mm

83 cm rigid copper brake hose for 3.5 mm diameter
- End fittings Male / Male- End fitting type: M8 x 125- Thread length: 20 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using an 8mm wrench.

Rigid copper brake hose 36 cm for 3.5 mm diameter
- Male / Male ferrules- End fitting type: M8 x 125- Thread length: 20 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using an 8mm wrench.

Rigid copper brake hose 70 cm for 4.75 mm diameter
- Male / Male ferrules- Nipple type: 7/16" 20UNF- Thread length: 21.5 mm- Internal diameter of ferrules: 5 mm
Made in Europe, our copper pipes are more malleable than steel and can be formed by hand.
In addition to its flexibility, copper is highly resistant to pressure, corrosion and temperature.Each pipe is fitted with steel fittings adapted to your vehicle, and is assembled using a 12mm wrench.