Floor

This top closure panel for for Acadiane (03/1978-03/1987) is a quality remanufacture.

This top closing panel for Acadiane is of higher quality than the original. Made in Europe, it is manufactured from electro-galvanized sheet metal of greater thickness than the original.

Compatible models :
- Acadiane type AY-CD: 03/1978 to 03/1987

Quarter floor front left driver side length 67cm for BMW 02 series E10 Sedan:

- All models 1502 to 2002Turbo from 03/1966 to 07/1977

The dimensions of this plate are designed to facilitate installation and ensure a perfect fit on the body.

ATTENTION: For the left-hand drive (LHD) version, it does not include the raised part where the bottom bracket is fitted!

Enclosed by insulation and carpeting, the BMW E10's floorboards are showing the effects of time, with perforating rust and various impacts underneath. Partial replacement by quarter-flooring will enable targeted bodywork restoration while respecting the original dimensions.

This quarter floor is delivered bare in black storage paint. Before final painting, it must be treated and prepared to prevent corrosion from reappearing.

Give your E10 a high-quality body part!

This metal repair plate is called "adaptable" because it does not come from the manufacturer.

DANSK front axle mounting bearing for Porsche 911 type F, G and 912 from 1965 to 1989 :

- Porsche 911 type F :

- 911 2.0 from 1965 to 1967
- 911 2.0 S from 1967
- 911 2.0 T / L / S from 1968
- 911 2.0 T / E / S from 1969
- 911 2.2 T / E / S from 1970 to 1971
- 911 2.4 T / E / S from 1972 to 1973
- 911 2.7 Carrera RS from 1973

- Porsche 911 type G :

- 911 2.7 from 1974 to 1977
- 911 S 2.7 from 1974 to 1977
- 911 Carrera 2.7 from 1974 to 1976
- 911 Carrera 3.0 from 1976 to 1977
- 911 SC 3.0 from 1978 to 1983
- 911 Carrera 3.2 from 1984 to 1989
- 911 Turbo 3.0 from 1975 to 1977
- 911 Turbo 3.3 from 1978 to 1989

- Porsche 912 :

- 912 1.6 - 90 hp (616.36) from 1966 to 1969

The bracket is sold individually , and two quantities are required per vehicle.

Sheet metal clamp for holding carpet in place.
Profiledin metal for welding along the slide bar.
Left or right side, sold individually.

For VW Beetle Saloon/Cabriolet
+ Mexico & Karmann-Ghia type 14
Years: 01/1969 ->2004
Chassis: from no. 119 476 295->

Dimensions :- Length: 81cm- Width: 59cm- Height: 10cm
Sheet thickness: 1.7mm
Information: There is no welded reinforcement under the sheet.

DANSK repair sheet for front trunk floor for Porsche 911 type F, G and 912 from 1965 to 1989:

- Porsche 911 type F:

- 911 2.0 from 1965 to 1967
- 911 2.0 S from 1967
- 911 2.0 T / L / S from 1968
- 911 2.0 T / E / S from 1969
- 911 2.2 T / E / S from 1970 to 1971
- 911 2.4 T / E / S from 1972 to 1973
- 911 2.7 Carrera RS from 1973

- Porsche 911 type G:

- 911 2.7 from 1974 to 1977
- 911 S 2.7 from 1974 to 1977
- 911 Carrera 2.7 from 1974 to 1976
- 911 Carrera 3.0 from 1976 to 1977
- 911 SC 3.0 from 1978 to 1983
- 911 Carrera 3.2 from 1984 to 1989

- 911 Turbo 3.0 from 1975 to 1977
- 911 Turbo 3.3 from 1978 to 1989

- Porsche 912:

- 912 1.6 - 90 hp (616.36) from 1966 to 1969
- 912 E 2.0 - 90 hp (923.02) from 1976

Front left-hand cab floor pan

For VW Combi Bay Window T2B
Years: 08/1972 ->07/1979
since chassis no. 213 2000 001->

This front crossmember screw for 2cv vans - 10X135mm is compatible with all models.

This front axle retainer screw is compatible with all models.
It allows the front axle to be attached to the chassis.

Complete passenger-side half floor for BMW 02 series E10 Sedan:

- All models 1502 to 2002Turbo from 03/1966 to 07/1977

ATTENTION: For the RHD right-hand drive version, the opening for the bottom bracket must be made, the floor being full without holes, so that it can also be adapted to the LHD left-hand drive version!

Enclosed by insulation and carpeting, the BMW E10's floorboards are showing the effects of time, with perforating rust and various impacts underneath. Replacing them in their entirety will enable the body to be restored to its original dimensions.

This half-floor, comprising in 1 piece the front and rear sections (from the firewall to the rear seats), is delivered bare in black storage paint. Before final painting, it must be treated and prepared to prevent corrosion from reappearing.

Give your E10 a high-quality body part!

This metal repair plate is called "adaptable" because it does not come from the manufacturer.

Right rear floor mat for Renault 5 (1972-1984)

For Renault 5 all models from 1972 to 1984

This high-quality right rear underfloor panel replaces the lower part under the right floor.

1/2 Front apron, set of inner and outer plates forming the lower bulkhead on the tunnel behind the pedals. To be welded. Brazil repro quality model.

For Beetle 1200, 1300, 1500, up to ->07/1967
up to chassis N°->117 999 000.

Left frontfloor for Mini Austin:
- Compatible with all Mini Austin versions from 06/1959 to 12/1974 including Mini Austin 1300 GT 68hp model.
This body panel is delivered in storage paint. It will need to be treated and prepared to prevent corrosion from reappearing. Before final painting, it is essential to carry out a blank assembly to check alignment and adjustment on the body.

Repair sheet metal for left side floor (driver's side) for Citroën ID.
Replacement sheet metal for restoring the left side floor (passenger side) of Citroën IDs.
Manufactured to original dimensions, this sheet enables restoration to manufacturer specifications.
Subject to water and mud splashes, as well as external aggression, the lateral area of the floor is particularly prone to perforating corrosion. This part is designed to replace damaged or weakened sections, ensuring a sound base prior to cabin reassembly.
Dimensions: 1495x243mm

This right-hand boot bottom corner for 2cvs before 1970 is high quality.
The right rear boot bottom gusset is made of electro-galvanised steel.
This repair panel is the link between the boot floor and the rear light panel.

Repair sheet metal for Citroën DS under-floor tank.
Replacement sheet metal for restoring the floor under the Citroën DS fuel tank.
Manufactured to original dimensions, this sheet enables restoration to manufacturer specifications.

Front left-hand quarter floor panel repair panel.

For VW Old Beetle 1200/ 1303 Hatchback & Convertible
Years : from 08/1972->
Chassis 1200 : from N° 113 2000 001->
Chassis 1303 : from N° 133 2000 001->
Chassis Convertible : from N° 153 2000 001->

This adhesive tape between chassis and body for 2cvs before 1970 - 10m isolates the body from the chassis.

Essential when reassembling the car after dismantling, this adhesive foam strip protects and insulates the body from the chassis, reduces noise and prevents corrosion.

Right-hand half-floor template
with T-shaped seat rails
Wolfsbürg West USA.

For VW Beetle Hatchback, 08/1970 ->07/1972
1200, 1300, 1500, 1302.
up to chassis no. 111 2000 001 ->112 3200 000.

Right-side replacement sheet metal half-floor
Model with central dome.
Top quality manufacturing with "thick sheet metal"

For Beetle, all models from 08/1972->
Saloon & Cabriolet: 1200 & 1303
from chassis no. 113 2000 001->

DANSK front floorpan for Porsche 914-4 and 914-6 :

- 914-4 1.7 - 80 hp (022-W) from 1970 to 1973
- 914-4 1.7 - 80 hp (022-EA) from 1972 to 1973
- 914-4 1.7 - 72 hp (022-EB) from 1972 to 1973
- 914-4 1.8 - 85 hp (021-AN) from 1974 to 1976
- 914-4 1.8 - 76 hp (022-EC) from 1974 to 1976
- 914-4 2.0 - 95 hp (039-GA) from 1973 to 1974
- 914-4 2.0 - 100 hp (039-GB) from 1973 to 1976
- 914-4 2.0 - 88 hp (039-GC) from 1975 to 1976
- 914-6 2.0 - 110 hp (901.36/37/38/39) from 1970 to 1972