Floor

1/2 Front apron, set of inner and outer plates forming the lower bulkhead on the tunnel behind the pedals. To be welded. Brazil repro quality model.

For Beetle 1200, 1300, 1500, up to ->07/1967
up to chassis N°->117 999 000.

1/2 Front apron, set of inner and outer plates forming the lower bulkhead on the tunnel behind the pedals. To be welded. Brazil repro quality model.

For Beetle 1200, 1300, 1500 since 08/1967-> from chassis no.
from chassis N° 118 000 001-> / 158 000 001->
(except 1302

Repair plate under master cylinder under frame head

For VW cox (08/1965-)

Section located under and behind the rear bench seat
(white section on the photo)

This rear crossmember screw for 2cv vans - 10X135mm is compatible with all models.

This long chassis screw is used to fix the rear axle clevises on the chassis of all 2cv models and derivatives.

The high forces absorbed by this screw require the use of high quality dichromated steel.

This front crossmember screw for 2cv vans - 10X135mm is compatible with all models.

This front axle retainer screw is compatible with all models.
It allows the front axle to be attached to the chassis.

DANSK front axle mounting bearing for Porsche 911 type F, G and 912 from 1965 to 1989 :

- Porsche 911 type F :

- 911 2.0 from 1965 to 1967
- 911 2.0 S from 1967
- 911 2.0 T / L / S from 1968
- 911 2.0 T / E / S from 1969
- 911 2.2 T / E / S from 1970 to 1971
- 911 2.4 T / E / S from 1972 to 1973
- 911 2.7 Carrera RS from 1973

- Porsche 911 type G :

- 911 2.7 from 1974 to 1977
- 911 S 2.7 from 1974 to 1977
- 911 Carrera 2.7 from 1974 to 1976
- 911 Carrera 3.0 from 1976 to 1977
- 911 SC 3.0 from 1978 to 1983
- 911 Carrera 3.2 from 1984 to 1989
- 911 Turbo 3.0 from 1975 to 1977
- 911 Turbo 3.3 from 1978 to 1989

- Porsche 912 :

- 912 1.6 - 90 hp (616.36) from 1966 to 1969

The bracket is sold individually , and two quantities are required per vehicle.

DANSK repair sheet for front trunk floor for Porsche 911 type F, G and 912 from 1965 to 1989:

- Porsche 911 type F:

- 911 2.0 from 1965 to 1967
- 911 2.0 S from 1967
- 911 2.0 T / L / S from 1968
- 911 2.0 T / E / S from 1969
- 911 2.2 T / E / S from 1970 to 1971
- 911 2.4 T / E / S from 1972 to 1973
- 911 2.7 Carrera RS from 1973

- Porsche 911 type G:

- 911 2.7 from 1974 to 1977
- 911 S 2.7 from 1974 to 1977
- 911 Carrera 2.7 from 1974 to 1976
- 911 Carrera 3.0 from 1976 to 1977
- 911 SC 3.0 from 1978 to 1983
- 911 Carrera 3.2 from 1984 to 1989

- 911 Turbo 3.0 from 1975 to 1977
- 911 Turbo 3.3 from 1978 to 1989

- Porsche 912:

- 912 1.6 - 90 hp (616.36) from 1966 to 1969
- 912 E 2.0 - 90 hp (923.02) from 1976

This rear crossmember screw for DYANEs and Acadianes - 10X135mm is compatible with all models.

This long chassis screw is used to fix the rear axle clevises on the chassis of all DYANEs and Acadianes.

The high forces absorbed by this screw require the use of high quality dichromated steel.

This front crossmember screw for DYANEs and Acadianes - 10X135mm is compatible with all models.

This front axle retainer screw is compatible with all models.
It allows the front axle to be attached to the chassis.

This rear crossmember screw for Meharis - 10X135mm is compatible with all models.

This long chassis screw is used to fix the rear axle clevises on the chassis of all Meharis.

The high forces absorbed by this screw require the use of high quality dichromated steel.

This front crossmember screw for Meharis - 10X135mm is compatible with all models.

This front axle retainer screw is compatible with all models.
It allows the front axle to be attached to the chassis.

This rear crossmember screw for 2cvs is compatible with all models.

This long chassis screw is used to fix the rear axle clevises on the chassis of all 2cv models and derivatives.

The high forces absorbed by this screw require the use of high quality dichromate steel.

This rear crossmember screw for 2cvs before 1970 - 10X135mm is compatible with all models.

This long chassis screw is used to fix the rear axle clevises on the chassis of all 2cv models and derivatives.

The high forces absorbed by this screw require the use of high quality dichromated steel.

This front crossmember screw for 2cvs before 1970 - 10X135mm is compatible with all models.

This front axle retainer screw is compatible with all models.
It allows the front axle to be attached to the chassis.

Repair plate for left floor under pedals for VW Transporter T25 / T3 from 05/1979 to 07/1992.

Driver's side rear quarter floor to be welded to the chassis.
Standard quality, supplied without seat rail.

For VW Kübel 181, (08/1968-)

Rear floor repair plate for VW Transporter T25 / T3 pick-up from 05/1979 to 07/1992.Length : 1500 mmWidth: 400 mmThickness: 1 mm

This rear crossmember screw for AMI 6 and AMI 8 cars - 10X135mm is compatible with all models.

This long chassis screw is used to fix the rear axle clevises on the chassis of all AMI 6 and AMI 8 cars.

The high forces absorbed by this screw require the use of high quality dichromated steel.